Table of Contents
Advertisement
Quick Links
Saphir Range
Installation, Operating and Maintenance Manual
For Models
Saphir 1
Saphir 2
Saphir 3
Saphir 4
Saphir 7
Saphir 10
(Saphir, Saphir+ and
Saphir Pro Systems)
Designed & Manufactured in the UK
015
01787 370187
info@darouv.co.uk
darouv.co.uk
Unit 9 Ballingdon Hill Ind. Est. Sudbury Suffolk CO10 2DX
Systems designed and manufactured by Daro UV in the UK, other requirements considered.
Daro UV is a company registered in England & Wales. Registration Number: 06070435.
Advertisement
Table of Contents
Summary of Contents for Daro Saphir Series
- Page 1 01787 370187 info@darouv.co.uk darouv.co.uk Unit 9 Ballingdon Hill Ind. Est. Sudbury Suffolk CO10 2DX Systems designed and manufactured by Daro UV in the UK, other requirements considered. Daro UV is a company registered in England & Wales. Registration Number: 06070435.
-
Page 2: Range Features
Saphir Range Range Features The Saphir range of systems is available with three different levels of technical features, Standard, Plus(+) and Pro. The features for each system are detailed below. Saphir Systems Standard Plus (+) • • • UK designed and manufactured •... - Page 3 Saphir Range Description The units are designed for the ultraviolet disinfection For single-pass applications, it is best to install the of water between 5°C and 23°C and can be fitted unit close to the point of use, removing the need anywhere in a water system provided the maximum to store large volumes of treated water.
- Page 4 Safe Disposal and Risk Due to Damaged Lamps The lamps used in the Saphir Systems are filled with Daro UV Systems provides a lamp replacement gas and mercury vapour at low pressure. Although service which includes the safe disposal of the they will not explode if broken there is a toxicity risk used lamp.
-
Page 5: Installation
Saphir Range Installation • Open the worm-drive clips to their maximum and fit over the chamber. Place the chamber on the wall Installation must be carried out prior to making any brackets, slip the clips into the slots on the brackets electrical connections. - Page 6 Saphir Range Mounting Parts Control box wall-mount brackets Chamber wall-mount bracket Worm-drive Clip small large Saphir 10 wall-mount brackets Quartz clamp key The accessory pack contains the following: Quantity Control Box Control Box Worm Clip Worm Clip Wall Bracket Quartz Clamp Model Supplied Bracket (A)
- Page 7 Saphir Range Electrical The socket is capped if this feature is not used. This unit must be installed by a qualified electrician. See specifications, below, for relays ratings. The Saphir range is supplied with a standard, BS1363 Connections UK mains plug and should be connected to an Terminal 1 - relay common.
-
Page 8: Maintenance
Saphir Range The lamp will continue to operate after 12-months of Note: If the lamp has failed and the lifetime has running time, but the UV output will be reduced, and it expired the three-second alarm sequence will begin. will be more likely to fail as it continues to age. The display gives an indication of the age of the lamp. - Page 9 Saphir Range Cleaning In the event that sediments build up on the surfaces 5. Do not attempt to clean the inside of the quartz of the quartz sleeve occasional cleaning will be sleeve – they are sealed in normal use and this is required.
-
Page 10: Specifications
Saphir Range Specifications Stock Code / Model Saphir 1 Saphir 2 Saphir 3 Saphir 4 Saphir 7 Saphir 10 Chamber material - 316 stainless steel Flow (litres/min)* Lamps GER15SE GER25SE GER25XOSE GER36SE GER36XOSE Lamp life - hours 8760 8760 8760 8760 8760 8760... -
Page 11: Warranty Terms
Warranty Terms This warranty will become void if the unit(s) are not All faulty parts must be returned to Daro UV Systems installed and operated according to the instructions for inspection and repair or replacement. Daro UV in the manual. - Page 12 Saphir Pro Setup & Calibration - Saphir Pro Models To set up the system must be connected to 230VAC. Use button red to select menu change. Keep pressing to skip to next parameter. Use buttons grey or white to change settings for any one parameter. (Grey increases values, white decreases values.) Hold the buttons down to scroll through values more quickly.
- Page 13 Saphir Pro Procedure On powering the system, the version of software will be displayed followed by the standard screen display of hours and UV intensity. To display the menu, press the red button for two seconds. The “lock code” displays, to prevent unauthorised access. Use the grey and white buttons to enter the correct code if changed from the default.
- Page 14 Saphir Pro Press the red button again to set language. Scroll through options with the grey and white buttons. Press the red button again to set date and time (mm.dd.yy). Change values with the grey and white buttons. Press the red button again to change the lock code. Change values with the grey and white buttons.
- Page 15 Saphir Pro Press the red button again to access “switch cycles”. This records the number of power downs of the system. Press the white button to clear and the red button to confirm. Press the red button again to access “startup time”. This sets a delay from power up to when monitoring starts.
- Page 16 Saphir Pro 10 Press the red button again to access “user counter”. This records the hours from the previous reset. This is used to record lamp hours since previous changes. Press the white button to clear and red button to confirm. 11 Press the red button again to access “abs counter”.
- Page 17 Saphir Pro 13 Press the red button again to access “input photodiode”. This is a pre-set configuration. Please DO NOT CHANGE. 14 Press the red button again to access “endvalue”. This is pre-set to 100%. Please DO NOT CHANGE. 15 Press the red button again to access “adjust” to calibrate the system. Using the up button (grey) or down(white) button change “no?”...
- Page 18 Saphir Pro 16 Press the red button again to access “main alarm”, to amend the UV threshold setting. The display flashes red and volt the free contacts will also switch. 17 Press the red button again to access “delay”, to add a time delay before the main alarm is triggered.
- Page 19 Saphir Pro 19 Press the red button again to access “delay”, to add a time delay before the pre-alarm is triggered 20 Scroll to “config”, press the red button to confirm. The new settings will be applied. Settings Setting Default Value Lock code 0000 Lamp life time...
- Page 20 Saphir Range Notes 01787 370187 info@darouv.co.uk darouv.co.uk...
- Page 21 Saphir Range Notes 01787 370187 info@darouv.co.uk darouv.co.uk...
- Page 24 01787 370187 info@darouv.co.uk darouv.co.uk Unit 9 Ballingdon Hill Ind. Est. Sudbury Suffolk CO10 2DX Systems designed and manufactured by Daro UV in the UK, other requirements considered. Daro UV is a company registered in England & Wales. Registration Number: 06070435.