NETGEAR RBS50Y - Orbi Outdoor Universal Satellite Quick Start Guide
![]()
Get Started
You can set up your Orbi Outdoor Universal Satellite in Orbi mode or Extender mode:
- Orbi mode. Set up your satellite in Orbi mode if you have an Orbi router.
![]()
- Extender mode. Set up your satellite in extender mode if you have a router or gateway that is not an Orbi router.
![]()
Set Up Your Satellite in Orbi Mode
By default, the satellite is set to Orbi mode. If you want to set up your satellite in Extender mode, see Set Up Your Satellite in Extender Mode.
- Place your satellite in an area near your Orbi router.
Note: You can place your satellite outdoors after the setup process.
- Connect your satellite to a power source.
The Power LED on the back of your satellite lights. If the Power LED does not light, press the Power On/Off button.
- Wait for the bottom Light LED to light white.
The following LED behavior occurs during booting:
- Pulsing white. The satellite is booting.
- Solid white. The satellite finished booting and is ready to sync with your Orbi router.
- Press the Sync button on the back of your satellite, and within two minutes, press the Sync button on the back of your Orbi router.
- Wait for your satellite to sync with your Orbi router.
The bottom Light LED on the satellite lights white while it attempts to sync with your Orbi router, and then lights one of the following colors:
Blue. Good connection
The Orbi router and satellite synced and the connection is good. The LED lights blue for three minutes and then turns off.
Amber. Fair connection
The Orbi router and satellite synced but the connection is fair. Consider moving the satellite closer to the router.
The LED lights amber for three minutes and then turns off.
Magenta. Connection failed
The Orbi router and satellite failed to sync. The LED does not turn off if it lights magenta. Move the satellite closer to the router and try again.
It might take about six minutes for your satellite to sync.
Your satellite uses the same WiFi network credentials as your Orbi router.
Move and Place Your Satellite After Installation
- Move your satellite outdoors and connect it to a power source.
Note: The recommend temperature range for your satellite is 4°F to 122°F (-20°C to +50°C).
- Make sure that the bottom Light LED lights blue to indicate a good connection to the router.
- (Optional) Mount your satellite.
You can wall-mount your satellite or place it on a stand. For more information, see Wall-Mount the Satellite or Attach the Satellite to the Stand in this quick start guide.
Note: After your satellite syncs with your router, the satellite's Sync button is disabled for security reasons. If you press the Sync button and the satellite's bottom Light LED pulses magenta, this LED behavior indicates that the Sync button is disabled.
If your satellite is in Orbi mode, to enable the Sync button, log in to the Orbi router web interface and go to the Attached Devices page. For more information, see the user manual.
If your satellite is in Extender mode, to enable the Sync button, log in to the extender web interface and go to the LED and Sync page. For more information, see the user manual.
Change the Mode Back to Orbi Mode
To change your satellite from Extender mode back to Orbi mode, do the following:
- Press the Power On/Off button and power off the satellite.
- Press and hold the Sync button.
- Hold the Sync button, and at the same time, press and release the Power On/Off button (don't release the Sync button).
Your satellite powers on.
- Continue to hold the Sync button.
- Wait for the bottom Light LED to pulse white and blue, then release the Sync button.
The following LED behavior occurs after you release the Sync button:
- Pulsing white. The satellite is booting and changing to Orbi mode. The LED pulses white for a few minutes.
- Solid white. The satellite is in Orbi mode and is ready to sync with your Orbi router.
Troubleshooting
During the setup, if you don't see the correct LED color as described in the setup steps, try the following:
- Place the satellite closer to the router.
- Check if your satellite is powered on.
- If you think your satellite is in the wrong mode, follow the steps in Change the Mode Back to Orbi Mode (follow these steps even if you think your satellite is already in Orbi mode) and check the LED behavior.
After you release the Sync button in the last step, if the bottom Light LED pulses white, the satellite is in Orbi mode. If the LED pulses blue, the satellite is in Extender mode.
Orbi Outdoor Satellite Overview
![NETGEAR - Orbi RBS50Y - Overview Overview]()
- Top Light LED
- Bottom Light LED
- LED On/Off button
- Sync button (also used for WPS connection)
- Reset button
- Power LED
- Power On/Off button
- Power connector
Support
Thank you for purchasing this NETGEAR product. You can visit https://www.netgear.com/support/ to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources.
For regulatory compliance information including the EU Declaration of Conformity, visit https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
![]()
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non-NETGEAR trademarks are used for reference purposes only.
November 2018
![]()
![]()
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download NETGEAR RBS50Y - Orbi Outdoor Universal Satellite Quick Start Guide
Need help?
Do you have a question about the Orbi RBS50Y and is the answer not in the manual?
Questions and answers