INNO BRA220R Installation Instructions

Cargo Box BRA220R Installation Instructions
These instructions are for the installation and use of the Inno carrier system attachment. After reading this manual, keep it in a safe place along with the
installation instructions for the rest of your carrier system.
PRECAUTIONS
Do not overload your cargo box. Maximum load
capacity varies by vehicle. Check the appropriate
limits for your car in the Fit Guide and your vehicle
owner's manual and determine your maximum
loading capacity with the formula below.
Use the lower of the 2 options below
-
Max load of Weight of
OR
vehicle or cargo box
cross bar
The Cargo box includes the parts listed below. Verify that they are included with the
carrier you have purchased. In the event any of these is missing, contact our service
center as listed at the end of this manual.
NO. Parts
1
Rooftop Box
1
Knob
2
3 U-Bolt
2 3 4
Plate
4
5 Strap
6 Strap Hook
7 Hole Covering
5 6 7
8 Molding
Key
9
Manual Instruction
10
10
8 9
4
Attach the Box to front cross bar with Plate, U-Bolt and Knobs. Make sure that
the ring on the Plate is on the side nearest the side of box.
Ring
Plate
Front Plate
Ring
Rear
Cross Bar
Cross Bar
A
U-Bolt
U-Bolt
Warning
Make sure to tighten the right
and left knobs evenly so that
Cargo Box
the U-bolt sits square with the
bar.
If U-bolt is not tightened
correctly, it may allow the box
to come loose.
U-Bolt
Cross Bar
7
Thread Strap trough two Rings on each side of the box and
fasten. Attach Strap Hooks inside box lid just above Straps.
Strap Hook
Buckle
Box Lid
Strap
Buckle Ring
Before driving the vehicle, shake the rack in
all directions to ensure that there is no
looseness in any of the mounting knobs and
screws. Retighten any loose knobs or screws.
1
If using an aftermarket base rack system, make sure that it is installed properly
according to the procedures described in the installation instructions for that rack.
CAUTION
Qty The distance between the front and rear crossbars should be at least 60cm ( 2 feet )
2
1
Temporarily put the Box on cross bars. And ①Insert key, turn clockwise and ②
8
push button to open the Box.
4
4
2
2
6
3
2
Adjust the location of the Box to align with holes at A.
key
2
Rooftop Box
1
A B
Front
Cross Bar
5
Tighten right and left knobs alternately to secure the Box to cross bar.
Rear
Front
Knob
B
U-Bolt
U-Bolt
6
Front - Place plugs into the 6 unused holes to seal
Rear - Trim Molding to the proper size and insert into slot.
Front
Rear
Molding
Plug
U-Bolt
U-Bolt
Cut Molding to this size.
8
Push Box in all directions to make sure that there is no
loosenesss. If you notice any play in the box, retighten 8 Knobs.
5411-71089G
9
Insert Key into key cylinder and turn it clockwise to "Open" position. Lift Box Lid by
pushing release button.
10
Unfasten Buckle and hang Straps on Strap Hooks to keep them out of the way while
loading. Load cargo. Unhook Straps and fasten it to secure cargo from moving while
driving.
Strap Hook
Strap
12
push button
Try to lift the lid at the latch points shown below to make sure that the hooks
have full engaged with the latches.
Turn Key counter clockwise to the CLOSE position.
2
Check at these points
Genuine Inno Replacement Parts
The following genuine replacement parts are available for this Inno carrier system
component. Specify the part number when ordering parts from your dealer.
Note
Specifications and the appearance of the carrier system and genuine replacement
parts are subject to change without prior notice in the interest of product
improvement.
Knobs
U-Bolt
Fit Kit
Contact Information
If you have any questions or comments, please contact us at the service center listed below. CarMate shall not be held liable for any accidents or incidental losses arising
from improper installation or use, nor for those arising from installation or use after the customer has made any change to the system's original configuration or specifications.
Car Mate USA
383 Van Ness Ave., Suite 1603
Torrance, CA
www.innoracks.com
support@rv-inno.com
Caution
Leave Key in key cylinder until Box is closed to avoid locking it in the box
Box lid
accidentally.
Release button
2
1
11
To close lid, make sure that Key is in the OPEN position. Make sure that Hooks line
up with latches and close Box all the way.
Buckle
ISP952 Strap
(2 pack)
Knobs (2 pack) Plate
Key
Hook
Hook latches
ISP682 Strap Hook
(2 pack)
ISP193 Molding ISP588 Hole Plugs
(2 pack) (4 pack)
Key(Verify Instruction Manual
Key number)