Related Manuals for LORENZ MESSTECHNIK GM 40
Summary of Contents for LORENZ MESSTECHNIK GM 40
- Page 1 Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Operation Manual DIN Mounting Rail SG Measuring Amplifier GM 40...
-
Page 2: Imprint
Imprint Manufacturer, Place Lorenz Messtechnik GmbH, D-73553 Alfdorf Valid for... DIN Mounting Rail SG Measuring Amplifier GM 40 Copyright Note © 2012 – 2015 Lorenz Messtechnik GmbH, Alfdorf Interdiction of Reprint Reprint in whole or in part with written permission, only. -
Page 3: Notes
For the sake of clarity, this operation manual may not constitute a detailed use of Lorenz Messtechnik GmbH devices in all possible applications. Also, not all possible types of installation, operation and maintenance are considered. -
Page 4: Intended Use
It is also pointed out that all obligations of Lorenz Messtechnik GmbH are exclusively arising from the respective sales contract in which the warranty is conclusively settled. Intended Use Lorenz Messtechnik GmbH devices may only be used for measurement tasks and the directly related control tasks. -
Page 5: Safety And Caution Symbols
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Safety and Caution Symbols If residual risks occur while working with the device, the following symbols in this operation manual must be noted: Warning: Warns of a potential risk of serious life-threatening injuries. The accident preven- tion regulations of the employer’s liability insurance association must be consid-... -
Page 6: Continuative Documents
D-73553 Alfdorf Fax +49 7172/93730-22 Continuative Documents Following documents contain reference information about the DIN Mounting Rail Measuring Amplifier GM 40 080552.pdf, data sheet of the DIN Mounting Rail Measuring Amplifier GM 40 E-Mail: info@lorenz-sensors.com Technical changes are under reserve 090120k Internet: www.lorenz-sensors.com... -
Page 7: Table Of Contents
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Contents Imprint ............................ 2 Notes ............................3 General Notes ....................... 3 Intended Use ......................... 4 General Dangers by not following the Safety Precautions ..........4 Residual Dangers ......................4 Safety and Caution Symbols .................. -
Page 8: Introduction
Introduction Product Description The DIN Mounting Rail Measuring Amplifier GM 40 amplifies signals of strain gauge sensors to stand- ard output signals. The slim housing shape allows space-saving installation in control cabinets on standard DIN mounting rails. The analog outputs of ±5V and ±10V enable direct signal processing with a PLC. -
Page 9: Instruction / Description Of The Operating Mode
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Instruction / Description of the Operating Mode Terminal assignment Terminal Assignment: U-voltage Output GND U/I Output I-Strom Output 10-30V DC Supply Supply Supply Supply - Supply + Shield... -
Page 10: Adjustment Of The Input Filter
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 6.3.3 Adjustment of the input filter The cutoff frequency of the 3DB input filter is adjusted by pot “filter”. Left Stop: Right Stop: Cutoff Frequency = 1kHz Cutoff Frequency = 10Hz The use of the filter is appropriate if interferences are on the measuring signal. -
Page 11: Interfaces And Connections
400Ω The exact device configuration is shown on the front side of the GM 40. If a GM 40 is ordered in con- nection with a sensor, it will be adjusted to the sensor; only the zero point must be corrected. -
Page 12: Troubleshooting
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Filter: At a high filter effect, interferences are better suppressed, however, a fast dynamic measurement is not possible. At a low filter effect, fast measurements are possible, but interferences must be reduced by other appropriate measures such as grounding, cable shielding etc. -
Page 13: Product Phases
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Product Phases Transportation Note: Please pack the equipment suitable for transportation The equipment may not be able to move back and forth in the package Please protect the equipment against moisture... - Page 14 The device does not contain any parts which must or can be serviced by the user. Repairs may be carried out by Lorenz Messtechnik GmbH, exclusive- ly. If assuming that safe operation of the device is no longer possible, it must be taken out of service and secured against inadvertent operation, immedi- ately.
-
Page 15: Safe Disposal
Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 Safe Disposal Equipment disposal: Please dispose obsolete equipment in accordance with the applicable statutory provisions. By this, you meet the legal obligations and also contribute to the environmental protection! E-Mail: info@lorenz-sensors.com... - Page 16 Obere Schloßstr.131 +49 7172/93730-0 LORENZ MESSTECHNIK GmbH D-73553 Alfdorf Fax +49 7172/93730-22 E-Mail: info@lorenz-sensors.com Technical changes are under reserve 090120k Internet: www.lorenz-sensors.com 16 of 16...