WoMaster DS101 Quick Installation Manual

Quick Installation Guide
Industrial 1-port Fast Ethernet
to Fiber Media Converter
DS101
www.womaster.eu
・Overview
The DS101 industrial media converter provides industrial-grade media
conversion between 10/100BaseT(X) and
connectors). The DS101 converters' reliable industrial design is excellent
for keeping your industrial automation applications running continuously
even under extreme operating temperature from -40 to 75°C. All DS101
converters are subjected to a 100% burn-in test.
Model Name Description
Industrial 1-port Fast Ethernet to Fiber Media
DS101-M-SC-2
Converter, multi-mode, 2km/1310nm, SC
Industrial 1-port Fast Ethernet to Fiber Media
DS101-M-ST-2
Converter, multi-mode, 2km/1310nm, ST
Industrial 1-port Fast Ethernet to Fiber Media
DS101-S-SC-30
Converter, single-mode, 30km/1310nm, SC
Industrial 1-port Fast Ethernet to Fiber Media
DS101-S-ST-30
Converter, single-mode, 30km/1310nm, ST
・Package Checklist
 1 x Product Unit

1 x 3-pin Removable Terminal Connector

1 x Attached Din Clip

1 x Quick Installation Guide
Optional Accessory (for detailed information please refer to the
Datasheet)
・Installation

DIN Rail mount

To mount the switch on the DIN Rail
track, insert the upper end of the
DIN‐Rail clip into the back of the
DIN‐Rail track from its upper side and
lightly push the bottom of the DIN‐Rail
clip into the track. The DIN Rail should
comply with DIN EN50022 standard.
Using wrong DIN rail may cause unsafe

installation.

Grounding Screw

For avoiding system damage by noise o r
electric shock, establish a direct connection by
insert the grounding wire into the GND contact
on the terminal block connector, then tighten
the wire-clamp screws. It is located at the
bottom of the switch.
V1+ V- V2+

DIP Switch Setting

In addition, the DS101 converter also
100BaseFX (SC/ST has a DIP switch to configure the
converter or store and forwarding
mode, RJ45 at 100Mbps half-duplex
or auto-negotiation, enable or disable
link loss forwarding. The table below
shows how to assign the DIP switch
dial to the corresponding function. The
table below shows how the DIP-switch
pin number is assigned to the function.
DIP Fast Con.
ON [ON] Set to
Converter
Mode
OFF [1] Set to
Store and
Forwarding
Mode
*Note：Please reboot the device, after you change the DIP
Switch Setting.
Grounding Screw

Wiring the Power Input

1) Insert the positive and negative wires into the
V1+, V- and V2+ contact on the terminal block
connector. (V- is the negative voltage shared by
the two power supplies)
2) Tighten the wire-clamp screws.
3) Connect the power wires to suitable DC
Switching type power supply. The input DC
voltage should be in the range of 9VDC to
60VDC.
TP Forced 100 Half
Fast Con. LLF En
TP Forced 100 Half LLF En
[ON] Set RJ45 in [ON] Enable
100Mbps Half Duplex LLF
Mode
[2] Set RJ45 in [3] Disable LLF
100Mbps Auto
Negotiation Mode
Fiber Ports (SC/ST)
DS101 is equipped with fiber ports. To connect the fiber port, remember to
link the Tx (transmit) port to the Rx (receive) port of the receiving device,
and the Rx (receive) port to the Tx (transmit) port of transmitting device.
Warning: Be careful when connecting the fiber port, the wrong
connection will cause the fiber port not working properly.
The picture below shows the fiber ports SC and ST appearance.
Duplex SC type Fiber port Duplex ST type Fiber port
・Appearance
DS101-M/S-SC/ST
System LED
・1x Power
・1x Mode
・1x LLF
・2x FX
- 1x LNK
- 1x FDX
1-port 100Base-FX
(SC/ST model)
1-port 10/100Base-TX
DIP Switch
・Forwarding Mode
・RJ45 mode
・LLF

LED Indicator

DS101-M/S-SC/ST
LED Status
Green On DC-IN Power is On
PWR
Off No Power in DC-IN
Green On
CON.
Off Store and Forward Mode
Red On LLF Event Occurs
LLF
Off No LLF Event Occurs
DIN Clip
Grounding
Screw
Power Connector
・1 x 3 pin terminal block
- 3 pin for power input
Description
Converter Mode