WoMaster DS201 Quick Installation Manual

Quick Installation Guide
Industrial Gigabit Ethernet Fiber
Media Converter
DS201
www.womaster.eu
・Overview
The industrial-grade fiber optic media converter DS201 can
operate in either low latency converter or switching store &
forward mode, it detects and changes to switch mode if the
copper and fiber speed or duplex are different. As an Ethernet
Media Converter, the Bi-directional Link-Loss-Forward (Link-
Fault-Pass-Through) is equipped and supports Auto-Recovery
if fault recovery.
The SFP socket supports 100Mbps or 1000Mbps fiber
transceiver, the 10/100/1000 RJ-45 also provided forced
10/100 Half for legacy device, those features could be
configured by DIP-Switch.
The 16Kbytes jumbo frame forwarding capability guarantees
high-speed Gigabit communications. Wide operation
temperature -40~75 C and heavy industrial EMC design
brings DS201 suitable for any industrial application
Model Name Description
Industrial Gigabit Ethernet Fiber Media Converter, 1
DS201 RJ-45, 1 SFP Socket, Redundant Power, DC
10~60V, AC18~30V, -40~75
・Package Checklist
 1 x Product Unit

1 x 4-pin Removable Terminal Connector

1 x Attached Din Clip

1 x Quick Installation Guide
・Installation

DIN Rail mount

To mount the switch on the DIN Rail track,
insert the upper end of the DIN‐Rail clip into
the back of the DIN‐Rail track from its upper
side and lightly push the bottom of the
DIN‐Rail clip into the track. The DIN Rail
should comply with DIN EN50022 standard.
Using wrong DIN rail may cause unsafe

installation.

Grounding Screw
For avoiding system damage by noise o r
electric shock, establish a direct connection
by insert the grounding wire into the GND
contact on the terminal block connector, then
tighten the wire-clamp screws. It is located at
the bottom of the device.
+
+

DIP-Switch Setting

In addition, the DS201 converter provides a
DIP-Switch to configure the convert setting.
The RJ-45 supports 10/100/1000Mbps in Auto
mode, and 10/100Half in forced mode. The
SFP fiber supports 100Mbps or 1000Mbps
SFP transceiver. Those features configured
by DIP-Switch. In the following table shows
the configuration. Ensure perform Power
Reset to enable new configuration after DIP-
Switch changed.
DIP No.
.
DIP 1
DIP 2
C
DIP 3
Note: Perform Power Reset to Active new features, once DIP
switch mode changed
DIN Rail Clip
Grounding Screw

Wiring the Power Input

1) Insert the positive and negative wires into the P1
(+,-) or P2 (+,-) contact on the terminal connector. (it
also supports polarity reverse function)
2) Tighten the wire-clamp screws.
3) Connect the power wires to suitable DC Switching
type power supply. The input DC voltage should be
in the range of 10VDC to 60VDC (Typical DC24V). It
also support low voltage AC input (18-30V) (+ /L, -/N)
TX 100H
LFP
Enable
ON
1 2 3
LFP
Disable
Auto
TX
Status Description
Link Fault Pass Through/
On
Link Loss Forward Enable
Off Disable (Default)
TX (RJ-45) Forced 100Mbps Half Duplex
On
mode
Off TX (RJ-45) Auto Negotiation (Default)
On 100FX:100Mbps SFP Transceiver
Off 1000FX: 1000Mbps SFP Transceiver (Default)
Fiber Port (SFP Socket)
DS201 is equipped with SFP socket which supports hot-swappable
function. User can install SFP transceiver with exactly transceiver
speed setting.
Warning: Be careful when connecting the fiber port, the wrong
connection will cause the fiber port not working properly.
SFP Transceiver ( LC Type Connector)
TX
・Appearance
System LED
• 1x Power
• 1x LFP
• 2x Fiber Status
SFP (100M/1000M)
RJ-45 (100M/1000M)
DIP Switch
• LFP (Off, On)
• RJ-45(Auto/Off, 100H/On)
• SFP Speed (1000M/Off,
100M/On)
Power Input
FX
• 4-Pin Removable Terminal
100
Connector
• Dual Power Input
• DC 10~60V, or AC 18~30V
・Auto Forwarding Mode Change
1000
DS201 deliver smart auto forwarding mode change function. If the
FX
RJ-45 link speed and duplex mode is not same as fiber port, then
it will auto change to Store and Forwarding mode with higher
forwarding latency.
With the same speed and duplex mode, the DS201 will active in
pure-converter mode with extreme low latency - 8.2x10
To obtain best network performance, please ensure both of RJ-45
and Fiber are linked in same speed and duplex mode.
・Link Loss Forwarding / Link Fault Pass Through
Link Loss Forwarding (LLF) or Link Fault Pass-Through (LFPT)
function is supported in DS201 when LFP LED blinking, please
check the cable connection. The event may cause by RJ-45 link-
down of local or far-end site, fault fiber connection. It is
recommended to enable the LLF function of both local and far-end
site to obtain a quick alarm.
(The LLF/ Link Fault Pass Through function supports bi-directional
forwarding and with auto recovery.)
RX
Steel Metal, IP31
DIN Rail Clip
Chassis
Grounding Screw
-9
Sec.