TC Helicon Perform-V - Vocal Processor Quick Start Guide

YOU WILL NEED...

MIC CONNECTION

CHARGING

SET GAIN

HEADPHONE & MIXER CONNECTION

FX ON/OFF

PRESETS

A Preset is a group of effects used to create an overall sound.

Changes made to Presets are saved automatically.

AUTO EQ

Tone automatically and dynamically adds EQ, compression, de-essing and gating to your voice.

ANTI-FEEDBACK

Anti-Feedback helps to eliminate squealing from your speakers. After all EQs have been used, Anti-Feedback will turn down the level.

PITCH CORRECTION

Pitch correction "nudges" you to the nearest semi-tone. It won't make a bad singer good, but it will subtly make your pitch more accurate.

FX BYPASS

Talk mode bypasses all of the effects so you can talk to the audience.

TAP TEMPO

Tap in time with your music to set the tempo for Echo. Tempo is global and not stored within the Presets.

CONDENSER MIC

If you have a condenser mic, MP-75 or MP-76, you will need to turn on +48V for it to work.

EFFECT EDITING

After the effect level reaches maximum, the LED ring resets and changes the style (sound) of the effect. The LED color also changes for each style.

PITCH METER

MUSIC IN

GET THE APP

www.tc-helicon.com/products/perform-v/support/

"BEAM" NEW SOUNDS

UPDATES & PRESETS

www.tc-helicon.com/products/voicesupport/

STAGE SETUP

ACCESSORIES

Important safety instructions

For service and warranty information, please go to:

http://www.tc-helicon.com/support/

The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Unplug this apparatus during lightning storms or when unused for long periods of time.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Do not use this product above 2000 m.

This equipment should be installed near the socket outlet and disconnection of the device should be easily accessible.

To completely disconnect from AC mains, disconnect the power supply from the AC receptacle. The mains plug of the power supply shall remain readily operable.

Do not install in a confined space.

Do not open the unit – risk of electric shock inside.

You are cautioned that any change or modifications not expressly approved in this manual could void your authority to operate this equipment.

Service: There are no user-serviceable parts inside. All service must be performed by qualified personnel.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.

Be advised that different operating voltages require the use of different types of line cord and attachment plugs. Check the voltage in your area and use the correct type.

To exchange the connector, always unplug the power supply first. Do not connect the power supply to an AC receptacle without the connector firmly and correctly attached to the power supply.

Observe: The DC output connector is polarized with + on the ring and - on the center. Always make sure that the polarity, voltage and current as specified on the power supply are compatible with a product before connecting the power supply to the product.

EMC/EMI

This equipment has been tested and found to comply with the limits for a Class B Digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For customers in Canada: This Class B digital apparatus complies with Canadian ICES-003.