1. Manuals
  2. Brands
  3. IRIS Spreaders Manuals
  4. Spreader
  5. IPS-200
  6. Operator's manual

IRIS Spreaders IPS-200 Operator's Manual

Pull-type spreader
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PULL-TYPE SPREADER
Fertilizer Spreader for ATV – Mod. IPS-200,200D,340,340D
OPERATOR'S MANUAL
& Please Read this operator's manual before operating the machine

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IPS-200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for IRIS Spreaders IPS-200

Summary of Contents for IRIS Spreaders IPS-200

  • Page 1 PULL-TYPE SPREADER Fertilizer Spreader for ATV – Mod. IPS-200,200D,340,340D OPERATOR'S MANUAL & Please Read this operator's manual before operating the machine...

  • Page 2: Table Of Contents

    - INDEX - 1. Introduction ..................... 1 2. Technical data ....................2 3. Parts ........................3 4. How to Operate .................... 4-5 5. Important safety information ..............5 6. Checkup ......................... 6 7. Storage ........................6 8. Spreading Chart .................... 7-8 9.

  • Page 3: Introduction

    1. Introduction 1) Power source is not necessary since it is operated by rotating the wheel. 2) The spreading angle can be adjusted.(Three spreading patterns) 3) Adjust the spreading amount by adjusting lever. 4) Yellow poly hopper makes rust free and visible inside 5) It can spread by ATV and compact tractor.

  • Page 4: Technical Data

    2. Technical data Model IPS-200 IPS-200D IPS-340 IPS-340D HOPPER CAPACITY(ℓ) 200/79.3 340/89.8 Electric Electric Outlet Shutter Control Mechanic Mechanic control control WEIGHT OF THE MACHINE 76/167.5 80/176.4 (㎏/lbs) WIDTH(outside side) 1150/45.2(Tire 15x6-6) 1230/48.4(Tire 18x8.5-8) (㎜/inch) LOADING HEIGHT(㎜/inch) 1175/46.2 1400/55.1 LENGTH(㎜/inch)

  • Page 5: Parts

    3. Parts Pull-Type Spreader (IPS-200,200D,340,340D) ➀ ➆ ➁ ➇ ③ ④ ➄ ➅ ➈ ➉ ➀ Ex/Hopper ➁ Hopper ➂ Frame ➃ Vanes ➄ Disc ➅ Tires ➆ Lever ➇ Prevention Plate ➈ Rod for tongue adjustment ➉ Tongue - 3 -...

  • Page 6: How To Operate

    4. How to Operate 1) Connect the links of spreader to the links of ATV or a small tractor. 2) Check for horizontality after fastened the equipment to ATV or a tractor. 3) If the horizontality is not maintained, use the horizontality-maintaining pole to do so.

  • Page 7: Important Safety Information

    8) You may require an additional adjustment by moving the individual vanes when the condition of fertilizer changes(weight, condition(wet or dry), etc) Moving the vane tips forward(No.1) will carry more material to the lefthand side. Moving the vane tips backward(No.3) will allow more material to be spread to the righthand side Please have a test spreading after each adjustment.

  • Page 8: Checkup

    6. Checkup 1) Make sure to apply Lubricant where needed and check for loosen nuts and bolts before operating. 2) Check for air pressure on the tires. 3) Test drive the equipment before actual use. 7. Storage 1) When the equipment is to be stored for a long time, apply lubricants to the area where it is likely to have corrosion.
  • Page 9 8. SPREADING CHART FOR FERTILIZER – METERS SPREAD VEHICLE QUANTITY TO BE SPREAD, IN KGS PER HECTARE AT CONTROL LEVER SETTING INDICATED FERTILIZER WIDTH SPEED TYPE (METERS) (km/h) 193.5 895.5 1237.5 1980 2461.5 3132 3600 Coarse Grain 100.1 257.5 456.3 764.7 1170.2 1198.8...

  • Page 10: Spreading Chart

    SPREADING CHART FOR FERTILIZER – FT SPREAD VEHICLE QUANTITY TO BE SPREAD, IN KGS PER HECTARE AT CONTROL LEVER SETTING INDICATED FERTILIZER WIDTH SPEED TYPE (METERS) (km/h) 193.5 895.5 1237.5 1980 2461.5 3132 3600 Coarse Grain 100.1 257.5 456.3 764.7 1170.2 1198.8 1216.3...

  • Page 11: Parts Sales & Trouble Shooting

    Parts sales 1) The parts list provided is in compliance with IPS-200,200D,340,340D standards. Refer to this list when order any parts. 2) Follow next steps as below when order parts: ex) We would like to order 1 unit of hopper...

  • Page 12: Part List

    11. Part list 1–Full Layout - 10 -...
  • Page 13 1–Full Layout PART DESCRIPTION Hopper Parts Frame Parts Alxe&Gearbox Parts Shutter Parts Drawbar Drawbar brace A Drawbar brace B Pin ∅19x90 Lock Pin A ∅10 R Pin ∅22 Pin ∅22x143 Pin ∅22x90 SUS Bolt, Hex Head M8x45 SUS Flange Nut, M8 Bolt, Hex Head M12x80 Washer, M12 Spring Washer, M12...
  • Page 14 2-Hopper Parts Layout PART DESCRIPTION Extension Hopper Hopper Flange Nut, M8 Washer, M8 Bolt, Hex Head M8X25 - 12 -...
  • Page 15 3-Frame Parts Layout - 13 -...
  • Page 16 3-Frame Parts Layout - 14 -...
  • Page 17 3-Frame Parts Layout PART NO. DESCRIPTION Frame Lock Nut, M10 SUS Nut, M10 SUS Spring Washer, M10 SUS Wing Nut, M10 SUS Bolt, Hex Head M10X20 Spreading Prevention Plate SUS Bolt, Hex Head M10X25 Spreading Direction Left and Right SUS Lock Nut, M10 Small Square Washer Carriage Bolt M10X30 Big Square Washer...
  • Page 18 4-Axle&Gearbox Parts Layout - 16 -...
  • Page 19 4-Axle&Gearbox Parts Layout PART NO. DESCRIPTION SUS Bolt, Hex Head M8X15 Vane Spreading Disc SUS Spring Washer, M8 SUS Nut, M8 SUS Bolt, Hex Head M8X20 Spreading Disc Holder SUS Lock Nut, M8 Socket Set Bolt M8x16 Spreading Shaft Fixing Bushing Key 8x7x25mm Spreading Shaft SUS Bolt, Hex Head M8X50...
  • Page 20 5-Shutter Parts Layout PART NO. DESCRIPTION SUS Flange Nut, M8 Lower Agitator SUS Bolt, Hex Head M8X45 SUS Nocking Bushing Fertilizer Discharger SUS Flange Nut, M10 SUS Washer M10 SUS Carriage Bolt M10X30 Shutter Washer M30 Snap ring S-32 - 18-...

  • Page 21: Assembling Instructions

    12-1. Assembling instructions for IPS MODEL 1) AXLE&GEARBOX 2) FRAME 3) DRAWBAR SET A) Fix the drawbar tube on the proper bracket of the axle&gearbox by 1 PIN ∅22x143 and 1 R PIN ∅22 - 19-...
  • Page 22 B) Fix the drawbar brace A on the proper bracket of the drawbar tube by 1 PIN ∅22x90 and 1 LOCK PIN ∅10 C) After put the frame on the axle&gearbox frame Fix the drawbar brace B on the proper bracket of the frame by 1 PIN ∅19x90 and 1 LOCK PIN ∅10 D) Fix the frame on the proper bracket...
  • Page 23 1) SPREADINGSHAFT ASSY 2) DISC AND VANES A) Fix the disk on the proper bracket of the spreading shaft assy' by 3 SUS SCREWS M8x20, 3 SUS LOCK NUTS M8 B) Tighten - 21 -...
  • Page 24 A) Fix the spreading shaft& disc assy' with the gearbox by 2 SOCKET SET SCREW M8 B) Tighten Be careful !! When you assemble, the wings are sharp - 22 -...
  • Page 25 1) DISCHARGER&SHUTTER 2) LOWER AGITATOR A) Fix the Discharger&Shutter on the proper bracket of the frame by 2 SUS CARRIAGE SCREWS 10x25, 2 SUS FLANGE NUTS M10, 2 SUS WASHERS M10, B) Tighten - 23 -...
  • Page 26 C) Insert the lower agitator and then fix the lower agitator on the shaft by 8 SUS SCREWS 8x45 and 1 SUS FLANGE NUTS M8 D) Tighten E) Fix the Bearing fixing plate on the proper bracket of the frame by 2 SCREWS M10x35, 2 NUTS M10 2 SPRING LOCK WASHERS M10 4 WASHERS M10,...
  • Page 27 G) Tighten - 25 -...
  • Page 28 1) PREVENTION PLATE 2) LEVER SET 3) LEVER SET A) Fix the prevention plate on the proper bracket of the frame by 2 SUS SCREWS 10x25, 2 SUS SPRING LOCK WASHERS M10, 2 SUS NUTS M10 B) Tighten - 26 -...
  • Page 29 C) Assemble the lever set D) Fix the adjusting bar on the proper hole of the shutter by 1 WASHER M10 and 1 RPIN E) Pull the lever all the way up - 27 -...
  • Page 30 F) Close the shutter G) Turn the lever pin to set the distance of adjusting bar between shutter and lever by 1 WASHER M10 and 1 RPIN - 28 -...
  • Page 31 1) EXTENSION HOPPER & HOPPER 2) BIG SQUARE WASHER & SMALL SQUARE WASHER & SCREWS&NUTS A) Place the hopper on the Fertilizer Discharger and Hoper Braces centering B) If the holes do not fit, drill these with a drill - 29 -...
  • Page 32 C) Fix the hopper on the proper bracket of the frame by 6 SHANK SCREWS M10x30, 6 LOCK NUTS M10, 1 BIG SQUARE WASHER, 2 SMALL SQUARE WASHERS (Big square washer → Small square washers) D) Tighten center first E) Tighten others - 30 -...
  • Page 33 F) Place the extension hopper on the hopper G) Make 10 hole for M8 to fix extension hopper on hopper by a drill machine with hole jig H) Fix the extension hopper on the hopper by 10 SCREWS M8x25, 10 FLANGE NUTS M8, 20 WASHERS M8 I) Tighten - 31 -...
  • Page 34 1) TIRE 15X6-6 or 18X8.5-8 or 20x10-8 A) Insert the tire&wheel assy' and then fix the tire&wheel assy' on the shaft of axle by 2 SUS SCREWS M8x45 and 2 SUS FLANGE NUTS M8 - 32 -...
  • Page 35 12-2. Assembling instructions for Electric Control 1) Frame 2) Gear lever and DC motor - 33 -...
  • Page 36 A) Paint the grease on the hole left side and right side - 34 -...
  • Page 37 B) Separate Bolt M10x65, Lock nut M10, Washer M10, Washer 10x30x6t and Spring from gear lever C) Assemble the gage pin with Bolt M10x65 and spring on the frame such as the left photo D) Assemble the Washer 10x30x6t the frame such as the right photo - 35 -...
  • Page 38 E) Paint the grease on Washer F) Assemble the gear lever G) Paint the grease on gear lever H) Assemble the washer M10 I) Assemble the Lock nut M10 and tighten (If too tight, the gear lever may not move) - 36 -...
  • Page 39 N) Assemble the DC motor upper hole on the frame with Bolt M10x25, Washer M10, Spring washer M10 and Nut M10 - 37 -...
  • Page 40 O) Paint the grease on gear teeth P) Align gear teeth and assemble the DC motor lower hole on the frame with Bolt M10x25, Washer M10, Spring washer M10 and Nut M10 Q) Tighten - 38 -...
  • Page 41 R) Connect DC motor connecter to controller connector and battery S) Fix the adjusting bar on the proper hole of the shutter by 1 WASHER M10 and 1 RPIN T) Close the shutter - 39 -...
  • Page 42 U) Turn the lever pin and operate controller to set the distance between shutter and gear lever and fix adjusting bar by 1 WASHER M10 and 1 RPIN V) Tighten stopper W) Open the shutter and tighten stopper - 40 -...
  • Page 43 X) Set gage pin on gage level and tighten(Closing) Y) Tighten DC motor cover - 41 -...

  • Page 44: Certificate Of Quality Assurance

    CERTIFICATE OF QUALITY ASSURANCE All products manufactured and sold by IRIS SPREADERS, Co. are designed and assembled in accordance with regulations on farm machinery under very strict quality management. If the product is managed and used in accordance with instructions on regular check-ups and maintenance schedule provided in the owner’s operation...
  • Page 45 ▶ On delivery the customer should check the censure that the machine has not been damaged in transit, and that it complies with that ordered as that it is complete with all the accessories as specified in the purchase contract. If it is found defective, a written complaint should be sent within 8 days of receipt of the same.
  • Page 46 3) Any malfunction or defect caused by using unspecified fuel (low quality fuel or contaminated fuel) 4) Any malfunction caused by not complying with instructions prescribed in Owner’s Operation Manual or Warning Signs 5) Any defect caused by unauthorized modification of the product or use of non-genuine parts.
  • Page 47 6. In case we upgrade the specifications of certain model, we do not have any responsibility to upgrade the already-sold-equipments. 7. TRANSFER OF WARRANTY Since we honor the remaining warranty time even after the transfer of ownership through sale or donation, it is very important to acquire the Certificate of warranty when transfer of the product takes place.
  • Page 48 WARRANTY INFORMATION ○ In order for us to guarantee our highest quality on our products, we offer complimentary inspections designated agencies. malfunction occurs caused by manufacturing defect during warranty period, we will repair or replace the parts at free of charge. ○...
  • Page 49 After Service Execution Report DATE PERFORMED TECHNICIAN CONFIRMED...

This manual is also suitable for:

Ips-200dIps-340Ips-340d

Table of Contents