1. Manuals
  2. Brands
  3. IRIS Spreaders Manuals
  4. Spreader
  5. IJS-200
  6. Operator's manual

IRIS Spreaders IJS-200 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FERTILIZER SPREADER
Fertilizer Spreader for tractor – Mod. IJS-200,200D,340,340D
OPERATOR'S MANUAL
& Please Read this operator's manual before operating the machine

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IJS-200 and is the answer not in the manual?

Questions and answers

Charlotte Wright
March 27, 2025

IRS 340 fertilizer spreader--where do I how to lubracate it at and with what?

0

Related Manuals for IRIS Spreaders IJS-200

Summary of Contents for IRIS Spreaders IJS-200

  • Page 1 FERTILIZER SPREADER Fertilizer Spreader for tractor – Mod. IJS-200,200D,340,340D OPERATOR'S MANUAL & Please Read this operator's manual before operating the machine...

  • Page 2: Table Of Contents

    - INDEX - 1. Introduction ..................... 1 2. Technical data ....................2 3. Parts ........................3 4. How to Operate ....................4-5 5. Important safety information ..............6 6. Checkup ......................... 7 7. Storage ........................7 8. Spreading chart ..................... 8-9 9.

  • Page 3: Introduction

    1. Introduction 1) The spreading Angle can be adjusted..(Three spreading patterns) 2) Stainless Steel Vanes and Disc. 3) Adjust spreading amount by adjusting lever. 4) Yellow poly hopper makes rust free and visible inside 5) Stainless steel vanes, Disc and prevention plate 6) Heavy duty frame 7) Transmission gearbox in stamped steel with high resistance gears.

  • Page 4: Technical Data

    2. Technical data Model IJS-200 IJS-200D IJS-340 IJS-340D HOPPER CAPACITY(ℓ/gallon) 200/52.8 340/89.8 Electric Electric Outlet Shutter Control Mechanic Mechanic control control WEIGHT OF THE MACHINE(㎏/lbs) 52.5/115.7 56.5/124.5 WIDTH(outside side)(㎜/inch) 1120/44 LOADING HEIGHT(㎜/inch) 900/35.4 1100/43.3 LENGTH(㎜/inch) 1120/44 SPREADING WIDTH(m/ft) 8-16/26-52.5 POWER P.T.O...

  • Page 5: Parts

    3. Parts Fertilizer Spreader(IJS-200,200D340,340D) ➀ ➁ ➇ ➆ ➂ ➃ ➄ ➅ ➀ Hopper ➁ Frame ➂ Discharger ➃ Prevention Plate ➄ Lower Link Pin ➅ Gearbox ➆ Disc ➇ Vane - 3 -...

  • Page 6: How To Operate

    4. How to Operate 1) Insert fertilizer spreader’s link to the tractor’s low links (both left and right) and fasten with the pins. 2) Connect and fasten the fertilizer spreader’s upper link to the tractor’s top link. 3) Close the outlet and pour fertilizer or seed into the hopper. 4) Adjust spread rate by using adjustment lever.
  • Page 7 7) You may require an additional adjustment by moving the individual vanes when the condition of fertilizer changes(weight, condition(wet or dry), etc) Moving the vane tips forward(No.1) will carry more material to the lefthand side. Moving the vane tips backward(No.3) will carry more material to be spread to the righthand side.

  • Page 8: Important Safety Information

    5. Important safety information 1) Safety gear must be worn while operating the machine. 2) If more than two people are operating the machine, observe the others’ movement carefully. 3) Make sure there is NO on or no obstacle within the operating area and its range.

  • Page 9: Checkup

    6. Checkup 1) Make sure to apply Lubricant where needed and check for loosen nuts and bolts before operating. 2) Before operating, please check for lubrication, and connection of the parts. 3) Test drive the equipment before actual use. 7. Storage 1) When the equipment is to be stored for a long time, apply lubricants to the area where it is likely to have corrosion.
  • Page 10 8. SPREADING CHART FOR FERTILIZER – METERS QUANTITY TO BE SPREAD, IN KGS PER HECTARE AT CONTROL LEVER P.T.O SPREAD TRACTOR SETTING INDICATED FERTILIZER TYPE SPEED WIDTH SPEED (RPM) (METERS) (km/h) 1022 1307 1556 Coarse Grain Fertilizers 1059 1093 12.0 Medium Grain Fertilizers 12.0 Fine Grain Fertilizers...

  • Page 11: Spreading Chart

    SPREADING CHART FOR FERTILIZER – FT QUANTITY TO BE SPREAD, IN LBS PER HECTARE AT CONTROL LEVER P.T.O SPREAD TRACTOR SETTING INDICATED FERTILIZER TYPE SPEED WIDTH SPEED (RPM) (FT) (mile/h) 1722 2253 2881 3430 Coarse Grain Fertilizers 1226 1830 2335 2410 1307 1545...

  • Page 12: Parts Sales & Trouble Shooting

    9. Parts sales & Trouble shootings Parts sales 1) The parts list provided is in compliance with IJS-340,340D standards. Refer to this list when order any parts. 2) Follow next steps as below when order parts: ex) We would like to order 1 unit of hopper Model Number Description...

  • Page 13: Part List

    11. Part list 1–Full Layout PART DESCRIPTION Hopper Parts Frame Parts Gearbox Parts Shutter Parts - 11 -...
  • Page 14 2-Hopper Parts Layout PART DESCRIPTION Extension Hopper Hopper Flange Nut, M8 Washer, M8 Bolt, Hex Head M8X25 - 12 -...
  • Page 15 3-Frame Parts Layout - 13 -...
  • Page 16 3-Frame Parts Layout PART NO. DESCRIPTION Frame Lock Nut, M10 SUS Nut, M10 SUS Spring Washer, M10 Low Link Pin(CAT1) Spring Washer, M22 Nut, M22 Spreading Prevention Plate SUS Bolt, Hex Head M10X25 Small Square Washer Carriage Bolt M10X30 Big Square Washer Lever Lever Fixing Pin Bolt, Hex Head M10X65...
  • Page 17 4-Gearbox Parts Layout PART NO. DESCRIPTION SUS Bolt, Hex Head M8X20 Spreading Disc Gearbox Lock Nut, M8 Bolt, Hex Head M8X25 SUS Lock Nut, M8 SUS Nut, M8 SUS Spring Washer, M8 Vane SUS Bolt, Hex Head M8X15 - 15-...
  • Page 18 5-Shutter Parts Layout PART NO. DESCRIPTION SUS Flange Nut, M8 Lower Agitator SUS Bolt, Hex Head M8X45 SUS Nocking Bushing Fertilizer Discharger SUS Flange Nut, M10 SUS Washer M10 SUS Carriage Bolt M10X30 Shutter Washer M30 Snap ring S-32 - 16-...

  • Page 19: Assembling Instructions

    12-1. Assembling instructions for IJS MODEL 1) FRAME 2) GEAR BOX 3) DISK & VANES A) Fix the disk on the proper bracket of the gear box by 3 SUS SCREWS 8x20, 3 SUS LOCK NUTS M8 B) Tighten - 17 -...
  • Page 20 C) Fix the gear box on the proper bracket of the frame by 6 SCREWS 8x25, 6 LOCK NUTS D) Tighten - 18 -...
  • Page 21 1) DISCHARGER&SHUTTER 2) LOWER AGITATOR A) Fix the Discharger&Shutter on the proper bracket of the frame by 2 SUS CARRIAGE SCREWS 10x25, 2 SUS FLANGE NUTS M10, 2 SUS WASHERS M10, B) Tighten - 19 -...
  • Page 22 C) Insert the lower agitator and then fix the lower agitator on the shaft by 8 SUS SCREWS 8x45 and 1 SUS FLANGE NUTS M8 D) Tighten - 20 -...
  • Page 23 1) PREVENTION PLATE 2) LOWER LINK PINS 3) LEVER SET 4) LEVER SET A) Fix the prevention plate on the proper bracket of the frame by 2 SUS SCREWS 10x25, 2 SUS SPRING LOCK WASHERS M10, 2 SUS NUTS M10 B) Tighten - 21 -...
  • Page 24 C) Fix the lower link pins to the frame by 2 NUTS M22, 2 SPRING LOCK WASHERS M22 D) Tighten E) Assemble the lever set - 22 -...
  • Page 25 F) Fix the adjusting bar on the proper hole of the shutter by 1 WASHER M10 and 1 RPIN G) Pull the lever all the way up H) Close the shutter I) Turn the lever pin to set the distance of adjusting bar between shutter and lever by 1 WASHER M10 and 1 RPIN - 23 -...
  • Page 26 1) EXTENSION HOPPER & HOPPER & FRAME ASSY’ 2) BIG SQUARE WASHER & SMALL SQUARE WASHER & SCREWS&NUTS A) Place the hopper on the Fertilizer Discharger and Hoper Braces centering B) If the holes do not fit, drill these with a drill - 24 -...
  • Page 27 C) Fix the hopper on the proper bracket of the frame by 6 SHANK SCREWS M10x30, 6 LOCK NUTS M10, 1 BIG SQUARE WASHER, 2 SMALL SQUARE WASHERS (Big square washer → Small square washers) D) Tighten center first E) Tighten others - 25 -...
  • Page 28 F) Place the extension hopper on the hopper G) Make 10 hole for M8 to fix extension hopper on hopper by a drill machine with hole jig H) Fix the extension hopper on the hopper by 10 SCREWS M8x25, 10 FLANGE NUTS M8, 20 WASHERS M8 I) Tighten - 26 -...
  • Page 29 IJS-340 - 27 -...
  • Page 30 12-2. Assembling instructions for Electric Control 1) Frame 2) Gear lever and DC motor - 28 -...
  • Page 31 A) Paint the grease on the hole left side and right side - 29 -...
  • Page 32 B) Separate Bolt M10x65, Lock nut M10, Washer M10, Washer 10x30x6t and Spring from gear lever C) Assemble the gage pin with Bolt M10x65 and spring on the frame such as the left photo D) Assemble the Washer 10x30x6t the frame such as the right photo - 30 -...
  • Page 33 E) Paint the grease on Washer F) Assemble the gear lever G) Paint the grease on gear lever H) Assemble the washer M10 I) Assemble the Lock nut M10 and tighten (If too tight, the gear lever may not move) - 31 -...
  • Page 34 N) Assemble the DC motor upper hole on the frame with Bolt M10x25, Washer M10, Spring washer M10 and Nut M10 - 32 -...
  • Page 35 O) Paint the grease on gear teeth P) Align gear teeth and assemble the DC motor lower hole on the frame with Bolt M10x25, Washer M10, Spring washer M10 and Nut M10 Q) Tighten - 33 -...
  • Page 36 R) Connect DC motor connecter to controller connector and battery S) Fix the adjusting bar on the proper hole of the shutter by 1 WASHER M10 and 1 RPIN T) Close the shutter - 34 -...
  • Page 37 U) Turn the lever pin and operate controller to set the distance between shutter and gear lever and fix adjusting bar by 1 WASHER M10 and 1 RPIN V) Tighten stopper W) Open the shutter and tighten stopper - 35 -...
  • Page 38 X) Set gage pin on gage level and tighten(Closing) Y) Tighten DC motor cover - 36 -...

  • Page 39: Certificate Of Quality Assurance

    CERTIFICATE OF QUALITY ASSURANCE All products manufactured and sold by IRIS SPREADERS, Co. are designed and assembled in accordance with regulations on farm machinery under very strict quality management. If the product is managed and used in accordance with instructions on regular check-ups and maintenance schedule provided in the owner’s operation...
  • Page 40 ▶ On delivery the customer should check the censure that the machine has not been damaged in transit, and that it complies with that ordered as that it is complete with all the accessories as specified in the purchase contract. If it is found defective, a written complaint should be sent within 8 days of receipt of the same.
  • Page 41 3) Any malfunction or defect caused by using unspecified fuel (low quality fuel or contaminated fuel) 4) Any malfunction caused by not complying with instructions prescribed in Owner’s Operation Manual or Warning Signs 5) Any defect caused by unauthorized modification of the product or use of non-genuine parts.
  • Page 42 6. In case we upgrade the specifications of certain model, we do not have any responsibility to upgrade the already-sold-equipments. 7. TRANSFER OF WARRANTY Since we honor the remaining warranty time even after the transfer of ownership through sale or donation, it is very important to acquire the Certificate of warranty when transfer of the product takes place.
  • Page 43 WARRANTY INFORMATION ○ In order for us to guarantee our highest quality on our products, we offer complimentary inspections designated agencies. malfunction occurs caused by manufacturing defect during warranty period, we will repair or replace the parts at free of charge. ○...
  • Page 44 Warranty Execution Report DATE PERFORMED TECHNICIAN CONFIRMED...

This manual is also suitable for:

Ijs-200dIjs-340Ijs-340d

Table of Contents