Download Print this page
Dell D7532QT Mechanical Instructions

Dell D7532QT Mechanical Instructions

Advertisement

Quick Links

Mechanical Instruction
Disassembly Procedures:
Step
S1. Remove the
Package_Buckles
and open the
carton.
S2. Remove the
desiccants
Figure
Desiccant *2
Desiccant *2
Remark
Remove he 6 pcs
Package_Buckles, then
use a proper tool to
open the carton. Uplift
the
top
paper-box
slowly.
Remove
EPS-TOP
accessories
bag(remote
control
and
battery(AA*2),
stylus*2pcs,
Power
cable(varies
contries),
HDMI
cable, DP 1.2 cable,
USB
3.1
Gen
upstream cable, Wire
Saddle *5 pcs and
QSG.
Take out 4pcs desiccant
from the bag. Use a
machine jip to take out
the whole monitor from
EPS-bottom. Remove
the PE bag from top to
bottom, and put the
monitor on ESD
protection foam.
the
and
PE
by
2.0
1

Advertisement

loading

Summary of Contents for Dell D7532QT

  • Page 1 Mechanical Instruction Disassembly Procedures: Step Figure Remark Remove he 6 pcs Package_Buckles, then use a proper tool to open the carton. Uplift paper-box slowly. Remove EPS-TOP accessories S1. Remove the Package_Buckles bag(remote control and open the battery(AA*2), stylus*2pcs, Power carton. cable(varies contries), HDMI...
  • Page 2 Step Figure Remark Turn off power, S3. Before Unplug external disassembly cables from product Use a Philips-head screwdriver to remove 8 screws for removing the DIE-CASTING. (No.1~8 screw size=M4x10; Torque=12±2kgf.cm) Use a Philips-head screwdriver to remove 17 screws for removing the Rear Cover.
  • Page 3 S5. Tear off the tapes,clips and disconnect all of the connectors Use a Philips-head screwdriver to remove 29 screws for removing the Main board,Power board ,OPS board, Converter board. S6. Remove the (No.1~23 screw Main board, size=M3x8 Power board ,OPS Torque= 4±1kgf.cm) board, Converter board,etc...
  • Page 4 Use a hexagonal screwdriver to remove 7 screws. (No.1~2 hex screw; size=M3x8 Torque=4±1kgf.cm) (No.3~5 hex screw; size=M3x5 Torque=4±1kgf.cm) (No.6~7 screw; Torque=4.5±0.5kgf.cm ) Use a Philips-head screwdriver to remove 5 screws for removing the BKT. (No.1~4 screw S7. Remove the size=M3x4 Torque=4±1kgf.cm ) (No.5 screw size=M4x6 Torque=4±1kgf.cm )
  • Page 5 No.1~4 screw size=M3x6 Torque=4±1kgf.cm) Use a Philips-head screwdriver to remove 4 screws for removing the S9. Remove the Speaker BKT Speaker BKT (No.1~4 screw size=M4x5 Torque=6±1kgf.cm...
  • Page 6 Product material information The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC. Capacitors / condensers (containing No used PCB/PCT) Mercury containing components No used Batteries Product has LR03 batteries Printed circuit boards (with a surface...
  • Page 7 Step Figure Remark Remove electrolyte capacitors (red mark) from printed circuit boards Take out bulk cap. pin solder with soldering Remove the big iron and absorber capacitors Lift the bulk cap up and take it away from the PCB...
  • Page 8 Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description: - Phillip-head Screwdriver - Hexagonal Screwdriver - Penknife - Soldering iron and absorber...