Williams AV Digi-Wave 400 Series User Manual
Digital transceiver and receiver
Hide thumbs
Also See for Digi-Wave 400 Series:
- Quick start manual ,
- User manual (66 pages) ,
- Quick setup manual (8 pages)
Related Manuals for Williams AV Digi-Wave 400 Series
Summary of Contents for Williams AV Digi-Wave 400 Series
- Page 1 Digi-Wave 400 Series ™ Digital Transceiver and Receiver USER MANUAL DLR 400 DLT 400 MAN 241I-1122...
-
Page 2: Table Of Contents
2-Year Warranty........................................... 32 Product Recycling: Please do NOT dispose of your Williams AV equipment in the household trash. Please take the equipment to an electronics recycling center or return the product to the factory for proper disposal. -
Page 3: System Overview
Internal Charging Contacts Microphone The Digi-Wave 400 Series is backward compatible with the 300 series with limited features. (For CHG 412) USB-C Charging Port It is not backward compatible with any earlier transceivers or receivers (DLT 100, DLT 100 2.0, DLR 50, DLR 60, and DLR 60 2.0). -
Page 4: General Operation
· Adjust the headset’s volume. Use the USB-C located on the bottom of DLT transceiver or the DLR 400 RCH Receiver, to charge the battery. Charge by either using a USB-C cable or using an approved, compatible Williams AV charging station. Talk Button ·... -
Page 5: The Main Screen
The Master 1 can override anyone else talking within the group. Master 2 has talking priority over Guests. • Each group must be assigned its own group number. Williams AV recommends a maximum of four The Master 1 or Master 2 must have their talk button deactivated to allow the Guest units to talk. When 2-6 groups using the system simultaneously within the same area to prevent interference. -
Page 6: Setting Up The Digi-Wave™ System
Digi-Wave 400 Series Digi-Wave 400 Series Setting Up the Digi-Wave™ System screen. Channel or Group is determined by your mode. A large or small clock is determined by the Master 1 settings. To change any of these settings, hold down the menu button. For instructions on configuring the Digi-Wave Settings of the Digi-Wave system should be selected based on how the system will be used. -
Page 7: Changing Settings
Digi-Wave 400 Series Digi-Wave 400 Series Changing Settings Example - Tour System The system has been configured so that up to four people can have open microphones and be talking at the same time. One DLT is set up as a Master 1 unit for the tour guide. Each tour member has a DLT transceiver set up If settings need to be adjusted later, the menu system can be reentered at any time by holding down the menu as a Guest unit. - Page 8 Digi-Wave 400 Series Digi-Wave 400 Series Example - Intercom Side Tone Adjustment One DLT transceiver is set up as a Master 1 unit. All other DLT transceivers are programmed as a Guest unit. Up This gives the user the ability to change the volume of their own voice as heard in the headset (side tone). This to six people can have open microphones and be talking at the same time.
-
Page 9: Interpretation Mode Features
Digi-Wave 400 Series Digi-Wave 400 Series Interpretation Mode Features To set the PIN: 1. Select whether or not the connection requires a PIN. If yes, you will be prompted to enter the desired PIN. Interpretation Mode has several features not available in other Digi-Wave modes. -
Page 10: Bilingual Mode
Digi-Wave 400 Series Digi-Wave 400 Series Bilingual Mode language requires their own DLT transceiver and interpreter. The audience member then listens to the channel for their specific language. Note: In previous Digi-Wave versions, this was known as Simultaneous Interpretation Mode. -
Page 11: Relay Mode
Ch. 2 English-Spanish and listening to Channel 1, and the floor cannot For older Digi-Wave 400 series units, a firmware update may be required to use Court Mode. listen to channel 1. Interpreters on other channels Ch 2 Group Selection... -
Page 12: Saving And Replacing Profiles
Power, Volume, Talk Talk unavailable settings. Mic level, and Group Ground The jack on the Digi-Wave 400 series is different than older devices. The Audio (right) wiring diagram in this section explains the internal wiring. See the pinout Voting function Not Available... -
Page 13: Updating Dlt 400 And Dlr 400 Rch Firmware
Power turned off Master device can’t be found Turn on Master unit The latest firmware and the Downloader can be found on the Williams AV website, linked to on the product’s automatically page. Press reset button on the back of device (DLT Power doesn’t turn off... -
Page 14: Specifications - Dlt 400 Transceiver
Digi-Wave 400 Series Digi-Wave 400 Series Specifications - DLT 400 Transceiver Problem Cause What to Do Out of Range Bring the unit closer to the Master Master is Off Turn Master unit on Dimensions 4.22”W x 2.60”H x 0.50”D (107.3 mm x 66 mm x 12.6 mm) -
Page 15: Specifications - Dlr 400 Rch Receiver
Digi-Wave 400 Series Digi-Wave 400 Series Specifications - DLR 400 RCH Receiver Battery Type: 2 x AAA Alkaline Batteries Battery Life: Alkaline Disposable (BAT 010-2): Up to 30 hrs Dimensions 4.22”W x 2.60”H x 0.50”D Power Save: Auto Sleep Mode after 5 minutes of no RF signal from compatible devices (107.3 mm x 66 mm x 12.6 mm) - Page 16 0.5 cm from the body. The SAR guideline Hereby, Williams AV declares that the transciever is in compliance with Directive 2014/53/EU and other Union includes a considerable safety margin designed to assure the safety of all persons, regardless of age and health.
-
Page 17: 2-Year Warranty
Williams AV shall not be liable to any person or entity for any medical expenses or any direct, incidental or consequential damages caused by any use, defect, failure or malfunctioning of the product, whether a claim for such damages is based upon warranty, contract, tort or otherwise.
Need help?
Do you have a question about the Digi-Wave 400 Series and is the answer not in the manual?
Questions and answers