Advertisement
Quick Links
MEMSHIELD 4 INSTALLATION INSTRUCTIONS FOR 400A PANELBOARDS/ PAN ASSEMBLIES
EM4PB840, EM4PB1440, EM4PB1840
EM4PBP840, EM4PBP1440, EM4PBP1840
Instruction Leaflet LT1222 (02/19)
IMPORTANT NOTES
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician in
accordance with current electrical engineering Codes of Practice, Requirements for the Electrical Installations (IET Wiring Regulations
BS7671), Construction (Design and Management) Regulations, HSG150 – Health and Safety in Construction, Statutory requirements
and any Specific instruction issued by the Company.
2. After completing the installation and testing of this product it is essential that this leaflet is drawn to the attention of the person
responsible for its future operation and maintenance, and is at all times available for ready reference.
3. The notes assume throughout that the product is disconnected from the supply. It is essential that this is done before any work is
carried out.
4. These Panelboards are only designed for use with EATON MCCBs. Failure to comply will result in invalid warranty and certification.
Panelboard's are supplied as Bottom Entry and Form 4 Type 6 Group Mounted without modification
Incoming Modules
400A Incoming MCCB EM4PBK404
Incoming
mount
General Note: When fixing M5 thread forming
screws tightening torque is 3.8 Nm
400A Incoming Neutral EM4PBNK40
Remove
incoming
mount.
Fit shield
Fit neutral
Bottom
Entry
400A Incoming Direct Cable EM4PBK404L
30Nm
Fit
Mount
30Nm
N
L1
31Nm
Remove
for access
31Nm
Remove
for access
L3
L2
L3
L2
L1
N
Secure
all
shields
4 Pole - Bottom Entry
Form 4 Type 6
3 Pole & Neutral - Bottom Entry
Form 4 Type 6 Group Mounted
Fit
Interphase
shields
4 Pole - Bottom Entry
Form 4 Type 6 Group Mounted
Click cover shield in to
incoming cover aperture
Secure
all
shields
Secure
all
shields
Advertisement
Related Manuals for Eaton MEMSHIELD 4
Summary of Contents for Eaton MEMSHIELD 4
- Page 1 3. The notes assume throughout that the product is disconnected from the supply. It is essential that this is done before any work is carried out. 4. These Panelboards are only designed for use with EATON MCCBs. Failure to comply will result in invalid warranty and certification. Panelboard’s are supplied as Bottom Entry and Form 4 Type 6 Group Mounted without modification...
- Page 2 Outgoing MCCB Adaptors and Neutral Modules NZM1 SPN Form 4 Type 6 Important all Adaptors: Fit MCCB with the adjustment dial end towards Compartmentalised/Group Mounted EM4PBFAN1L1-3N the adaptor stabs NZM1 - EM4PBFAN1L1-3N, EM4PBFAN14 EM4PBGMN1N, EM4PBCKN1N Group mounted when finger guard fitted Support fixings Support fixings NZM1 4 Pole Form 4 Type 6...
- Page 3 Box fixing, ensure scratch washers are fitted both sides Cableways, Extension/Corner/DIN Boxes and Plinths Extension/DIN Box- EM4PB250EX EM4PB250EXDIN Fits either end Corner Box- EM4PB300CX Fits either side Cableway- Cableway - Provision EM4PB68SXB to move earth bar into cableway, EM4PB1214SXB utilising earth strap EM4PB1618SXB Fits either side 15Nm...
- Page 4 Conversion to Form 4 Type 2/ Form 4 Type 6 Compartmentalised When converting to Compartmentalised, cableways must be fitted either side of panelboard Compartmentalise Module EM4PBCK Fix with 2 x M5 fixings Fix with Fix with 5 x M5 4 x M5 fixings per cover Fix with fixings...
- Page 5 Form 4 Type 6 Compartmentalised Outgoing Modules EM4PBCKN126, EM4PBCKN146, EM4PBCKN246 Fit compartment with 7 x M5 fixings (Example EM4PBCKN246) Prepare Adaptor NZM2 14Nm 15Nm Adaptor Assembly – Fit cover Interphase barriers to mccb with 8 x M5 Type 6 shield to carriage fixings Extension palms to mccb NZM1 4P...
- Page 6 Form 4 Type 2/6 Compartmentalised Blanking Way Lifting Eye Kit EM4PBLE EM4PBCKN12BK, EM4PBCKN14BK EM4PBCKN24BK Utilising existing M5 Fit blanking way screws with 2 x M6 fixings 3.8Nm Empty Compartment Pan Assemblies EM4PBP840, EM4PBP1440, EM4PBP18400EM4PBP1840 Drawn as 8 way pan with 400A incoming kit...
- Page 7 Label Fitting Ensure x7 labels supplied with panelboard are fitted in the correct places as shown in this bottom entry example. For top entry, the labels are in the same position but rotated through 180° Panelboard Labels 1 & 3 Supply label fitted to incoming cover Outgoing Adaptor Labels 2off labels supplied with outgoing adaptors to be fitted as shown...
- Page 8 Intellectual Property Rights! our control. Particular care should therefore be taken to follow the Eaton wishes to make it clear that it owns intellectual property rights in the instructions given here and to ensure their continued availability in product which it manufactures (whether or not listed in this leaflet) and that it conjunction with the use of the product.