Advertisement
Quick Links
Advertisement
Related Manuals for VELOWAVE ROVER
Summary of Contents for VELOWAVE ROVER
- Page 1 Instructions to Set Up Your VELOWAVE ROVER Diagram 1 / 16...
- Page 2 We know you are excited about getting going but please: ✓ Reseat and charge the battery before the first ride ✓ Make sure the pedals are tight ✓ Make sure the front wheel is installed properly and tight ✓ Inflate the tires properly ✓...
- Page 3 Assembling Your E-Bike 1) Read all of the instructions carefully. Be familiar with the proper operation of all items. 2) This quick guide is intended to list the steps needed to assemble your bike with some mechanical skills. It is not a complete manual or training. If you do not feel comfortable or lack some of the skills to assemble it yourself, reach out to a cyclist friend, a local bike mechanic or one of our support technicians for guidance.
- Page 4 Installing Your Handlebar 1) Place the handlebar in the handlebar mount being careful with the wires. 2) Face the mounting brackets on the front end of the mount with the round edges facing outward. Adjust the handlebar angle to your comfortable riding posture. 3) Secure the mounting brackets with four screws.
- Page 5 Installing Your Front Wheel 1) Insert the front wheel in between the front fork on the bike. Be sure the fork is resting on the outside of the axle. 2) Align the disk between the brake caliper as shown in Figure 2. 3) Insert the skewer into the wheel axle as seen shown.
- Page 6 Installing Your Headlight 1) Place the headlight with its bracket in front of the fork gantry. Push the screw provided on the headlight through the installing hole on the fork gantry. Tighten the fixing nut onto the screw. (You might need to secure the fixing nut tightly so the screw doesn’t turn). 2) Connect the headlight cable with the wire coming out from the downtube.
- Page 7 Installing Your Pedals 1) Warning: Incorrect installation will cause damage. Please read the instructions and watch our videos if needed. 2) Identify the Left and Right markings on the pedals. They can only be installed in their respective side. a. L is for the Left Pedal and it goes on the Left Crank Arm. b.
-
Page 8: Preparations Before Riding
Preparations Before Riding 1) Read all instructions carefully, be familiar with the proper operation of all items. Check for detailed information and guidance on our product page. 2) Warning: Basic electric precautions should always be followed to avoid issues or malfunction. How to Power on the Bike There are 3 gears in the power lock located at the upper side of the downtube. - Page 9 To unlock and Remove the Battery 1) Turn off the LCD display. Turn the key to the OFF gear to power off the bike. 2) Push the key inward and turn counterclockwise to unlock the battery. The battery will pop out. 3) Hold the battery with two hands and take it out from the tube.
-
Page 10: How To Use The Display
How to Use the Display 1) Power on/off Press the button to turn on the display. Your bike will be ON. Press again to turn it off. The display will automatically shut down when there is no operation or riding for 5 minutes. 2) Adjust the assist level Short press “+”... - Page 11 How to Charge Your Bike The battery can be charged when locked on the bike or unlocked and removed from the bike. 1) Remove the rubber cover on the charging port and insert the charger into the charging port. 2) Plug the charger into the power outlet. When the charger is plugged in, the LED light on the charger will turn RED to show that the battery is charging.
- Page 12 Notes of Charging and Storage: 1) Charging time of a 48V 15Ah battery takes about 8 to 10 hours when charging with a standard 2A charger. 2) Pay attention to check whether the surface temperature of the battery case rises too high during charging.
-
Page 13: Error Code
Error Code Error Error Notes Code Throttle has not returned to the start-up position. Check if the throttle Open Throttle Fault gets stuck. Try to return the throttle to the start-up position. Throttle Fault Throttle may be damaged. Check if the cable or throttle is damaged. The battery voltage is too low to operate. -
Page 14: Basic Troubleshooting
Basic Trouble Shooting SYMPTOMS CAUSES SOLUTIONS ⚫ ⚫ Battery off Turn on battery ⚫ ⚫ Battery installation Reseat battery ⚫ ⚫ LCD display not on Turn on LCD display Throttle and pedal assist not working ⚫ ⚫ Discharged battery Charge battery ⚫... - Page 15 Label of Your VELOWAVE 15 / 16...
- Page 16 To find out more, please visit our website at www.velowavebikes.com 16 / 16...