Advertisement
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons.
To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.
No naked flame sources – such as candles – should be placed on the product.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch.
This product is intended to be operated ONLY from the AC Voltages listed on the back panel or included power supply of the product. Operation from other voltages other than those indicated may cause irreversible damage to the product and void the product's warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power cord, use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel.
Klipsch powered subwoofers are designed to reproduce deep bass and deliver the impact that makes your movies and music come alive. For optimum performance, place your subwoofer in a corner of the room on the same wall as your front channel speakers.
Stereo Placement
Surround LCR and Rears Placement
Please note that room placement can have a dramatic effect on the performance of your powered subwoofer. Corner placement, as suggested above, will increase the amount of bass output, while placing the subwoofer along the middle of a wall, or out in the room will decrease the amount of bass output. Experiment with a number of different placement options and control settings to find the one that best suits your particular room and taste. When choosing your subwoofer's location, keep in mind that you will need to connect the subwoofer's built-in amplifier to an AC power outlet.
Optimal Connections – Klipsch SW powered subwoofers can be connected to the subwoofer output of your electronics via the RCA jack inputs ("LINE IN") on the subwoofer's rear panel. This can be in place of the conventional speaker wire connections ("SPEAKER LEVEL IN"). For more information on the controls mentioned in this manual and on bass management, see your dealer or visit www.klipsch.com.
Line Level Connections
Conventional Speaker Wire Connections – Using 16-gauge or larger speaker wire, connect the RED "positive" (+) terminal of your amplifier's LEFT channel to the RED (+) terminal of your subwoofer's LEFT channel input ("SPEAKER Level IN"). Connect the BLACK "negative" (-) terminal of your amplifier's LEFT channel to the BLACK "negative" (-) terminal of your subwoofer's LEFT channel input ("SPEAKER Level IN"). Repeat this procedure for connecting your amplifier's RIGHT channel to your subwoofer's RIGHT channel input. Take care to ensure that no bare wires from any of the connections touch any other terminals, as this could cause a short and damage your equipment.
Speaker Level Connections
"LINE IN/LFE" – This input is filtered by the built-in "Low Pass" (LP) crossover and is designed as a general purpose input for the subwoofer. It accepts the LFE signal output of your digital surround electronics.
"LOW PASS" (LP) Control – This control allows the user to select the upper frequency cutoff of the subwoofer. Frequencies above the control setting are filtered out, allowing you to blend the subwoofer's output with that of your main speakers. The frequency is selectable from 40-150Hz. For sources with an LFE output or that use an internal crossover, the lowpass filter should be defeated by setting the control to "BYPASS".
"VOLUME" – This control serves as an overall volume control for the subwoofer. It is used to match the output level of the subwoofer to the main speakers.
"PHASE" 0/180 – This control is used to acoustically match the subwoofer's output to your main speakers. Select the position either 0˚ or 180˚ in which your subwoofer has more output at the listening position.
"Power" ON/OFF– Klipsch SW subwoofers use a detachable power cord and do not have a main power switch. To fully remove power from the subwoofer, the power cord must be disconnected from the unit.
Auto/On – When this switch is in the "ON" position, the subwoofer will remain on at all times. When this switch is in the "AUTO" position, the subwoofer will automatically turn "on" when it senses a signal. It will automatically turn "off" after 15 minutes with no signal. When this switch is in the "OFF" position, the subwoofer will remain "off" until the switch is manually turned back to the "ON" or "AUTO" position.
LED indicator– Klipsch SW subwoofers have an LED indicator on the front that indicates the status of the built in amplifier. The LED will light blue when the amplifier is on and receiving a signal. When the unit is in standby mode or turned off, the LED indicator will turn off.
Your subwoofer has a durable vinyl finish that should only require dry dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based cleaners and harsh detergents. The brush attachment of your vacuum should remove any dust from your subwoofer enclosure.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the SW-350 that isn't answered in the manual? Leave your question here.