Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bissell CROSSWAVE PET
Summary of Contents for Bissell CROSSWAVE PET
- Page 1 CROSSWAVE® PET MODEL 2225F...
-
Page 2: Safety Instructions
SYMBOL EXPLANATION SYMBOL EXPLANATION Caution. Disconnect power before servicing. Use only BISSELL® cleaning formulas intended for use with this machine. Read operator’s manual. Check the manufacturer’s tag before Do not freeze. cleaning textile. “W” on the tag Risk of fire. -
Page 3: Table Of Contents
We love to clean and we’re excited to share one of our innovative products with you. We want your CrossWave Pet to work like new for the years to come, so this guide has tips on how to use, maintain and, if there’s a problem, troubleshoot. -
Page 4: Product View
Lower Cable Wrap Integrated Carry Handle Rinse Cup Dirty Water Tank Rinse and Storage Tray Your BISSELL® CrossWave® Pet comes in three • Handle easy-to-assemble components and does not • Body require any tools to assemble. It also comes with a •... -
Page 5: Assembly
Cleaning Formulas WARNING To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning formula intended for use with the hard floor device. CROSSWAVE® FORMULAS Keep plenty of BISSELL® formulas on hand so you... -
Page 6: Operations
A few notes about filling the clean water tank: • Fill with warm (140°F/60°C MAX) tap water and add the appropriate BISSELL® formula. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE. NOTE: Never put descaling, alcoholic, eucalyptus oil, or detergent products into the cleaner, as this may damage it or make it unsafe for use. - Page 7 TIP: For overly challenging and stuck-on messes on your hard floors, activate the RUG mode and hold your CrossWave® over the mess. Using short passes while holding the trigger allows the multi-surface brush to go to work. global.BISSELL.com 7...
- Page 8 NOTE: The RUG button dispenses twice the solution of the HARD FLOOR button to help with area rug cleaning. ATTENTION Do not overwet carpet. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure. 8 global.BISSELL.com...
-
Page 9: Maintenance & Care
Repeat as needed. Pull brush roll out by grabbing the Place the brush roll upright in the brush roll tab and pulling up. brush roll drying tray to dry. global.BISSELL.com 9... - Page 10 Put the machine away in a closet or basement until the next use. Store in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and may void the warranty. 10 global.BISSELL.com...
- Page 11 Hand wash the vacuum filter and screen with Rinse the float stack located at the bottom warm water and mild detergent. of the top of the dirty water tank. global.BISSELL.com 11...
- Page 12 Once parts are dry, Place strainer back into and push into place until you reassemble and replace the dirty water tank. hear a “click”. top of dirty water tank. NOTE: Tanks are NOT dishwasher or microwave safe. 12 global.BISSELL.com...
- Page 13 Then press foot. Press the window back into place until down to lock the pull tab into place. you hear a “click”. global.BISSELL.com 13...
-
Page 14: Troubleshooting
Cap of clean water tank is not closed Remove the clean water tank and reapply leaking properly the cap Too much water applied Go over area without spraying down water Machine is Previous floor care products used Contact product manufacturer regarding streaking how to remove 14 global.BISSELL.com... -
Page 15: Warranty
It gives you specific rights. It is offered as an additional benefit to Except as set out below, BISSELL and its distributors are not liable for any your rights under law. You also have other rights under The Australian... - Page 16 But wait, there’s more! Join us online for a complete guide to your new product, including troubleshooting, parts and more. Go to BISSELL.com. INFO VIDEOS PARTS ©2023 BISSELL Inc. All rights reserved. Part Number 1634570 10/22...
Need help?
Do you have a question about the CROSSWAVE PET and is the answer not in the manual?
Questions and answers
I machine isn’t sucking up the water?
The Bissell CrossWave Pet may not be sucking up water due to several possible issues:
1. Clogs or Blockages – Ensure there are no hair clogs or debris blocking the suction path.
2. Dirty or Faulty Filter – A clogged or old filter can restrict airflow. Try replacing it.
3. Improper Assembly – Make sure all components, including the dirty water tank and seals, are correctly attached.
4. Suction Motor Issues – If the motor is not functioning properly, it may not generate enough suction.
5. Dirty Water Tank Not Sealing Properly – Check if the tank is correctly seated and sealed.
6. Worn or Damaged Parts – Over time, parts may wear out, reducing performance.
If deep cleaning and replacing parts (like the filter) have not resolved the issue, there may be a mechanical failure requiring professional repair.
This answer is automatically generated