Related Manuals for Vanair EPEQ WELDER140
Summary of Contents for Vanair EPEQ WELDER140
- Page 1 W E L D E R 1 4 0 Instruction Manual Portable Li-ion Battery Welder Li-Ion 1.5 h 140A 604.8 Wh 14°F - 140°F Quick Charging WELDER140 Part Number: 282037...
- Page 2 Certification standards: FCC CE UN38.3 ROHS EAC The relevant design schemes and manufacturing technology used in this product are protected by patents. The copyright of this manual is owned by Vanair Manufacturing, Inc. Its contents are subject to change without notice.
-
Page 3: Table Of Contents
CONTENTS 1. Safety Tips and Precautions............2. Product Introduction..............3. Instructions for Use..............4. Troubleshooting................5. Maintenance, Storage, and Disposal......... 6. Service..................7. Packing List ................. 8. Replacement Parts..............9. Warranty ..................This manual will explain how to use the unit safely and effectively. Please read and follow these instructions and precautions carefully. -
Page 4: Safety Tips And Precautions
SAFETY TIPS AND PRECAUTIONS Please keep this User Manual and read it carefully before use. This user manual describes how to use the equipment safely and efficiently. Be sure to follow the instructions during its use. Beware of Electric Shock •... - Page 5 Beware of Arc Flash • Strong arc flash will be generated during welding. Therefore, a welding helmet with a qualified filter and cover should be used to prevent the eyes from being hurt by sparks or arcs when welding or observing the arc. •...
-
Page 6: Product Introduction
Note: If the welder needs maintenance and repair, call the Vanair Service ® Department at 844-VAN-SERV. If the user delivers the welder to an unauthorized service center for maintenance or repair, the user is no longer entitled to the manufacturer’s warranty service. - Page 7 Control Panel W E L D E R 1 4 0 800.526.8817 | EPEQ.com Description Name Note Window Important Note Digital Display Displaying Working Status / Welding Current Power Indicator Window Battery Indicator / Quick and Standard Charge Indicator Power Switch Turn On / Off the Welding Power Source Current Adjusting Knob Adjust the Welding Current...
- Page 8 Technical Details Description EPEQ WELDER140 Model ™ Battery Capacity 604.8WH Battery Type Lithium-Ion Input Voltage Range 100V - 240V AC Input Voltage Frequency 50/60HZ Charging Mode CC - CV 3 Hours / Standard Charge Charging Time 1.5 Hours / Quick Charge Charging Temperature Range 32°F - 113°F (0°C - 45°C ) Output Current Range...
-
Page 9: Instructions For Use
INSTRUCTIONS FOR USE Battery Level Checking 100% Capacity Under the power-off state, press the Battery 80% Capacity Button (J) to observe the remaining battery capacity through the Battery Indicator LED (C). The LED will turn off if the Battery Button (J) is 60% Capacity pressed again or no other operation is performed within 10 seconds. - Page 10 Welding Mode Note: The Lithium-Ion battery must be fully charged before first use of the welder. Make sure the equipment has a safety clearance of 1.5 ft (0.5 m) and there is no obstruction at the air inlet and outlet to ensure the cooling air enters and exits freely.
- Page 11 • Flip the Circuit Breaker (7) on the rear cover to the "ON" position. Press the Power Button (D) on the front panel; a green light will illuminate. Mixed mode will be automatically enabled and the welder is ready for operation. In the mixed mode, it will automatically switch to the quick charge mode and the charge mode switch will be locked;...
-
Page 12: Troubleshooting
Note: For other non-common failures, if multiple restarts cannot be recovered, try to restart the welder after pressing the reset button (K). If it is still unable to recover from the failure after restarting, please contact the Vanair Service ®... -
Page 13: Service
Please keep the warranty card. This product is warranted for one year from the date of purchase. This warranty does not cover failures caused by normal wear or misuse. For further details on warranty coverage and warranty information, please contact the Vanair Service Department at 844-VAN-SERV. ®... -
Page 14: Warranty
WARRANTY OR RETURNS MUST BE PRE-AUTHORIZED PRIOR TO PERFORMING ANY WARRANTY WORK. Vanair reserves the right to make changes in engineering, design, and specifications; add improvements; or discontinue manufacturing at any time without notice or obligation. Vanair, EPEQ, and the corresponding logos and ELECTRIFIED POWER EQUIPMENT, are registered logos or trademarks of Vanair Manufacturing, Inc., Michigan City, IN, USA. - Page 15 FOR SERVICE: CALL 844-VAN-SERV www.EPEQ.com Vanair Manufacturing, Inc. 10896 West 300 North, Michigan City, IN 46360 NOTE: Before disposing of damaged goods, check with your state Environmental Protection Agency to find out about special restrictions on the disposal of the lamp and batteries or return them to a...
- Page 16 800.526.8817 | EPEQ.com 10896 West 300 North | Michigan City, Indiana 46360 USA 090188-OP_r2-062222_NML...
Need help?
Do you have a question about the EPEQ WELDER140 and is the answer not in the manual?
Questions and answers