Advertisement
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable working area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non-stable workpiece with a clamp, vice or other adequate holding device.
3
3 Avoid unintentional starting.
3
DO NOT force the drill to achieve a task it was not designed to perform.
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the drill if damaged.
7
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
7
the drill when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and disposed of correctly.
7
DO NOT exceed the rated capacity of the drill.
DO NOT operate the drill if any parts are missing as this may cause failure or possible personal injury.
7
DO NOT leave the drill operating unattended.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT pull the cable from the power supply.
7
When not in use switch off the drill, remove plug from the power supply and do not leave until the tool has come to a complete stop.
7
3
2. DESCRIPTION
The GDM90B and GDM95B variable speed bench drills are suitable for light industrial, agricultural and woodworking applications. The drills
are fitted with flip-up safety guards and “No Volt Release” switches which prevent accidental restart after a mains power interruption. A rack and
pinion feed shaft with preset depth control for repetitive work is also included. Both models have Morse Taper Spindles to accept taper
shank bits. Mortice attachments and work clamps are also available, contact your local Sealey dealer for information.
3. TECHNICAL SPECIFICATIONS
Model
Chuck size (mm)
Spindle Nose Taper
Swing (mm)
Chuck to Upright Face (mm)
Spindle Travel (mm)
Number of Speeds
Speed Range (rpm)
Spindle to Table - max. (mm)
Spindle to Base - max. (mm)
Working Table Diameter (mm)
Working Base (mm)
Overall Base (mm)
Column Diameter (mm)
Overall Height (mm)
Voltage (AC)
Motor Range - no load (W)
- under load (W)
Weight (kg)
4. CONTENT
4.1. Package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your dealer immediately.
3 Head Assembly
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2 - table arm & bracket)
3 Safety Guard
3 Wedge
GDM90B
GDM95B
16
16
MT2
MT2
316
316
128
128
60
60
12
12
240 - 3000
240 - 3000
310
560
410
670
260
260
160 x 140
155 x 155
205 x 333
210 x 350
60
60
745
1000
230
230
370
370
550
550
30
32
3 Base
3 Feed Handles and Knobs (3)
3 Table
3 Bolts and Washers (4)
3 Arbor
3 Hex. Keys (2)
3 Chuck and Key
3 Table Arm, Bracket and Worm
3 Rack and Rack Ring
3 Screw (upper pulley cover)
3 Set Screws (2)
GDM90/95B - 0016 - (2) - 111000
Advertisement
