Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for swepac FB 515
Summary of Contents for swepac FB 515
- Page 1 FB 515 USER MANUAL IN ORIGINAL B00001 Doc: 101533-GB 2104...
- Page 2 FB 515...
-
Page 3: Table Of Contents
USE ................3 SAFETY INSTRUCTIONS ........4 STANDARDS ............4 SIGNS ..............5 TECHNICAL DATA ..........6 METHOD OF OPERATION FB 515 ...... 6 COMPONENT PLACEMENT ........ 7 DAILY SUPERVISION .......... 8 BEFORE STARTING ..........10 STARTING THE MACHINE ........ 10 STOPPING THE MACHINE ........ -
Page 4: Safety Instructions
FB 515 SAFETY INSTRUCTIONS STANDARDS Noise • Before using the machine, the operator must be informed Measurement according to the standard EN 500-4 Rev.1: of the manufacturer’s safety instructions and instructions 1998, Annex C: for use. Measurement uncertainty ± 0,5dB (A) i 95% of •... -
Page 5: Signs
FB 515 SIGNS Machine plate Warning Signs Before use, carefully read through the manual and safety regulations in order to be able to handle the machine in a proper manner. Make sure that the manual is always available 1. Manufacturer. -
Page 6: Technical Data
Battery capacity 40 Ah amount 0,4 litre Generator power 180 W (15 A) METHOD OF OPERATION FB 515 (hydraulically powered only) The machine consists of a base plate with vibrating elements and a top-mounted suspended plate. The cushioning between the base plate and the upper part consists of rubber dampers. -
Page 7: Component Placement
FB 515 COMPONENT PLACEMENT B00010 B00002 Left side view Right side view 1. Cap 11. Refueling 2. Yoke 12. Battery 3. Connection point, battery charge + (Some machines) 13. Hydraulic oil filter 4. Operating lever (forward/reverse lever) 14. Protective frame 5. -
Page 8: Daily Supervision
FB 515 DAILY SUPERVISION Check hydraulic oil level Check daily that the hydraulic connections are not leaking or wear out from driving. The oil level in the hydraulic oil tank Fuel Check must be as shown, at maximum 2 cm below the tank top. - Page 9 FB 515 Charging the battery Vibrating element Check for oil leaks regularly. Seal any leaks. NOTE! the machine must under no circumstances be operated if there are any indications of leakage. Note! Oil amount in the vibration element is 0,4 L.
-
Page 10: Before Starting
(the warn- ing light is present on all models, but is only used on cer- tain models). 9. Swepac Compaction Indicator (SCI). The lights are turned on from left to right as compaction progresses (some mod- els). -
Page 11: Stopping The Machine
FB 515 STARTING THE MACHINE DRIVING INSTRUCTIONS Put the key in its slot on the control panel. Press the Start/ Start and stop the machine’s vibration element with the Reset switch, press and hold the switch there for 1 second, vibration switch on the control panel. -
Page 12: Transportation
FB 515 TRANSPORTATION Transport security For transportation by vehicle, the lever must be in the forward position and secured with, for example, approved The machine has a lifting yoke. straps. Note! Secure it to the lifting yoke on the base plate and not the rubber-cushioned upper part. -
Page 13: Hydraulic Oil Pressure
Measurement of driving engine speed and vibration frequency is carried out with a stroboscope lamp with a graduated scale. Hydraulic pressure is measured with a manometer with a manometer outlet on the valve block, see image. Strobe lamp and manometer can be ordered from SWEPAC. Engine speed ......... 2900 r / min loaded Hatz Vibration frequency at hydraulic oil temp. -
Page 14: Hydraulic Schematic
FB 515 HYDRAULIC SCHEMATIC B00013 1) Hydraulic pump 6, 45cc 2900 RPM (Hatz) 5) Hydraulic cylinder Front/Back 2) Pressure relief valve max 200 Bar 6) Measuring outlet 3) Solenoid valve vibrations On/Off 7) Return oil filter 4) Hydraulic engine 4.09 4300 RPM... -
Page 15: Accessories
The lights indicate the compaction status of the substrate during operation. If no more lights flash, maximum compaction of the substrate has been reached. Swepac Compaction Indicator does not replace conventional test methods for degree of packing and is intended to provide the operator with useful information, such as finding areas that are not compacted or to... - Page 16 FB 515 NOTES...
- Page 17 FB 515 NOTES...
- Page 18 FB 515 NOTES...
-
Page 19: Ec Declaration Of Conformity
2. Type: FB515 3. Motor power: 7.5 kW The product complies with the following directives: 2006/ 42 / EC 2000 / 14 /EC 2004/108/EC EN 500-1 EN 500-4 Technical documentation available from: Swepac AB, Bergvägen 7 34132 Ljungby SE Tomas Johansson/Product Engineer... - Page 20 FB 515 SWEPAC AB Address Bergvägen 7, 341 32 Ljungby, tel 0372-156 00, fax 0372-837 41, Email mail@swepac.se, Internet www.swepac.com...
Need help?
Do you have a question about the FB 515 and is the answer not in the manual?
Questions and answers