Operating Instructions; Maintenance And Repair Instructions - Craftsman INCREDI-PULL 316.794711 Operator's Manual

STARTING/STOPPING INSTRUCTIONS
IF... the engine fails to start after a few attempts, move the choke lever to
Position 3 and pull the starter rope 3-8 times in a controlled motion. The
engine should start. If not, repeat.
IF WARM... If the engine is already warm, go back to step 6.
STOPPING INSTRUCTIONS
1. Release your hand from the trigger. Allow the engine to cool down by idling.
2. Press and hold the On/Off switch in the OFF (O) position until the unit
comes to a complete stop (Fig. 8).
USING THE SPEED START
NOTE: This unit can use a Speed Start
Please refer to the Speed Start
use of this feature. (Items Sold Separately! Refer to page 8 of this manual
for more information about these Speed Start
STARTING INSTRUCTIONS
NOTE: When starting the unit, make sure it is not directed at bystanders or
loose debris.
1. Check the oil level in the crankcase. Refer to Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling the
Unit.
NOTE: There is no need to turn the unit on. The On/Off Switch is in the ON ( I )
position at all times.
3. Fully press and release the primer bulb 10 times, slowly. Some amount of
fuel should be visible in the primer bulb (Fig. 9). If fuel cannot be seen in
the bulb, press and release the bulb until fuel is visible.
4. Move the choke lever to Position 1 (Fig. 9).
NOTE: The unit should be started in idle. Do not squeeze the trigger until
step 8 (Fig. 8).
5. Crouch in the starting position (Fig. 10). Insert the Speed Start
accessory into the Speed Start
Refer to the Operation section of the Speed Start
manual.
6. Do not squeeze the trigger. Run the Speed Start
seconds.
7. Do not squeeze the trigger. Move the choke lever to Position 2 (Fig. 9).
8. Do not squeeze the trigger. Run the Speed Start
intervals no longer than 2 seconds each until the unit starts.
9. Remove the Speed Start accessory from the unit.
TM
10. Squeeze and hold the trigger, or press down the cruise control (Fig. 8),
and allow the engine to warm up for 30 to 60 seconds.
11. Continue to squeeze the trigger. Move the choke lever to Position 3 (Fig. 9)
and continue warming the engine for an additional 60 seconds. The unit may
be used during this time.
IF... the engine does not start, go back to step 3.
IF... the engine fails to start after a few attempts, move the choke lever to
Position 3 and squeeze the throttle control. Run the Speed Start
accessory in intervals no longer than 2 seconds each until the unit starts.
IF WARM... If the engine is already warm, go back to step 7.
STOPPING INSTRUCTIONS
1. Release your hand from the trigger. Allow the engine to cool down by idling.
2. Press and hold the On/Off switch in the OFF (O) position until the unit
comes to a complete stop (Fig. 8).
6
ACCESSORY
TM
Accessory!
TM
accessory operator's manual for proper
TM
accessories.)
TM
TM
TM port on the side of the unit (Fig. 25).
accessory operator's
TM
accessory for 2
TM
accessory in
TM
HOLDING THE BLOWER
Before operating the unit, stand in the
operating position and check for the
following:
The unit is in the right hand and on
•
the right side of the body. Do not
block the air intake which will affect
the unit's performance (Fig. 11).
If the conditions are dusty, the
•
operator is wearing a dust mask or
face mask
The unit is in good working condition
•
The tubes are in place and secure
•
OPERATING TIPS
Using the Variable Speed Cruise Control
For longer periods of operation and to
eliminate possible finger fatigue.
1. Move the variable speed cruise
control toward the FAST position to
incrementally increase or maintain
the unit's engine speed (Fig. 12).
When the variable speed cruise
control is pressed, the trigger will
recede into the handle.
2. To decrease engine speed, move the
variable speed cruise control to the
SLOW position and the trigger will return to idle (Fig. 12).
Other Tips
Always use a firm grip when holding the unit.
•
To reduce the risk of hearing loss, hearing protection is required.
•
Operate power equipment only at reasonable hours when people might
•
not be disturbed. Comply with times listed in local ordinances. Usual
recommendations are 9:00 am to 5:00 pm, Monday through Saturday.
To reduce noise levels, operate the unit at the lowest possible speed to
•
do the job.
Use rakes and brooms to loosen debris before blowing.
•
Watch for bystanders, open windows or cars; blow debris safely away.
•
Use the curved tube extension so the unit can work closer to the ground.
•
Clean up after using blowers and other equipment. Dispose of debris
•
appropriately.

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the frequency stated in
TM
the table. These procedures should also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require special tools or skills. If
unsure about these procedures take the unit to Sears or other qualified
service dealer. Call 1-800-4-MY-HOME® for more information.
NOTE: Maintenance, replacement, or repair of the emission control devices
and system may be performed by a Sears or other qualified service dealer.
Call 1-800-4-MY-HOME® for more information.
NOTE: Please read the EPA statement that came with the unit for a complete
listing of terms and coverage for the emissions control devices, such as
the spark arrestor, muffler, carburetor, etc.
FREQUENCY
Every 10 hours
After 1st 10
hours
Every 40 hours

OPERATING INSTRUCTIONS

Cruise
Control
MAINTENANCE REQUIRED
Clean and oil air filter
Change oil
Check rocker arm to valve clearance and adjust
Change oil
Check rocker arm to valve clearance and adjust
Check spark plug condition and gap
Fig. 11
SLOW
FAST
Fig. 12
SEE
p. 7
p. 7
p. 7
p. 7
p. 7
p. 8