Advertisement
3.2.6. Drilling.
WARNING! Ensure that you read and understand Section 1 safety instructions
before using the drill.
1. If the workpiece to be drilled is loose it should be secured in a vice or with
clamps to keep it from turning as the drill bit rotates.
2. When drilling metals, use a light oil on the drill bit to keep it from overheating.
oil will prolong bit life and improve the drilling action.
3. for hard, smooth surfaces use a centre punch to mark desired hole location.
this will prevent bit from slipping as you start to drill.
4. A pilot hole may be necessary to assist the final size drill through the workpiece.
lock a pilot drill in the chuck. follow steps 5 to 8 below and drill a pilot hole at
the centre punch mark where the final hole is to be drilled. Insert the final sized
bit. Hold the drill firmly, place the tip of the bit in the pilot hole and depress the
trigger.
5. Move the drill bit into the workpiece applying only enough pressure to keep the
bit cutting.
DO NOT force the drill or apply side pressure to elongate the hole.
6. regularly withdraw the drill bit from the hole in order to clear cuttings.
7. ease the pressure of drilling when the bit is about to break through the far side
of the workpiece.
WARNING! Be prepared for drill bit binding or break through. When these situations
occur the bit has a tendency to grab and the drill will kick, which could cause loss of
control. If not prepared, this loss of control may result in damage and/or personal
injury.
8. If the bit jams in the workpiece or if the drill stalls, release the trigger switch
immediately. Place the drill in reverse to assist release of the bit.
9. After a long period of continuous operation, allow the drill to run with no load
and at maximum speed to cool the motor.
WARNING! Drill bits can become very hot during use. Allow to cool or hold
with a cloth for removal.
When finished, remove bit from chuck, clean drill, clean, and, if necessary,
re-sharpen bit and store in a safe, dry, childproof area.
4. MAINTENANCE
Cleaning.
4.1.
Keep the drill ventilation slots clean and free from obstructions. If available, blow compressed air into the vents to clear any
accumulated dust (safety goggles must be warn when undertaking this process).
Keep the outer case of the drill clean and free from grease. DO NOT wash with water or use solvents or abrasives.
recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is compatible
with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid
waste authority for recycling information.
to remove the batery refer to section 3.1.
Dispose of batteries according to local authority guidelines.
under the Waste Batteries and Accumulators regulations 2009, Jack sealey ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme.
Jack sealey ltd's Batteries Producer registration number (BPrn) is BPrn00705
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Environmental Protection.
Battery Removal.
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk,
IP32 7Ar
Original Language Version
fig.8
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
cP3014VHK, cP3018VHK
Issue: 5 - 11/01/12
Advertisement
