Advertisement
1.3.7. DO NOT pull or carry the appliance by attached leads.
1.3.8. DO NOT pull plug from socket by the power cable.
1.3.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
Note! This product is double insulated
a) Connect the BROWN live wire to the live terminal 'L'.
b) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
1.4.
BATTERY CHARGER SAFETY INSTRUCTIONS
WARNING! DO NOT attempt to charge any battery other than that supplied for the drill. Other types of batteries may explode!
All mains electrical supply safety features must be followed as described in section 1.3. above.
disconnect the charger from the mains power supply when not in use.
DO NOT expose the charger to damp or wet conditions.
DO NOT pull or carry the charger by the power lead.
DO NOT operate the charger if it has been dropped, received a sharp knock, or is damaged. take charger to an authorised agent.
DO NOT dismantle the charger as this may cause damage or personal injury and will invalidate your warranty.
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
DO NOT recharge a second battery pack immediately after charging the first. consecutive charging will overheat the charger. Allow the
unit to cool for 15 minutes before charging the next pack.
DO NOT attempt to connect two chargers together.
store the charger in the same manner as the battery pack, see section 1.2.
Risk of Hand Arm vibration Injury
cordless Hammer drill/driver model nos. cP3014VHK & cP3018VHK when operated in accordance with these instructions and tested in
accordance with Bs en 28662-1:1993, Iso 8662-1:1988 results in the following vibration emission declared in accordance with Bs en Iso
8662-6:1995, Iso 8662-6:1994
CP3014vHK
Measured vibration emission value: . . . . . .14.71m/s
uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . .5.88m/s
CP3018vHK
Measured vibration emission value: . . . . . .16.95m/s
uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . .6.78m/s
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
CP3014vHK. this tool should not be used by an individual regularly for more than 28 minutes in any 8 hour period.
CP3018vHK. this tool should not be used by an individual regularly for more than 21 minutes in any 8 hour period.
this duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
2. SPECIFICATIONS
Professional cordless drills featuring an extra powerful fan-cooled motor developing up
to 25nm (cP3014VHK) and 30nm torque (cP3018VHK). electronic variable speed in
forward/reverse and brake gives complete control. Wide range of torque settings over two
mechanical speeds including hammer action. Built-in spirit level allows for accurate drilling.
led battery level indicator prompts re-charging or switching to second battery (included).
13mm Keyless chuck for quick change of drill/bit and auxiliary handle with internal storage
for supplied 9pc bit set. supplied in robust carry-case with internal component storage
compartment.
Model No:
Battery type
no load speed
0-360rpm / 0-1300rpm (+/- 15%) 0-500rpm / 0-1700rpm (+/- 15%)
Impact rate
5760bpm / 20800bpm (+/- 15%) 8000bpm / 27200bpm (+/- 15%)
drilling capacities
Wood
Metal
concrete
chuck size
Maximum torque
replacement Battery
Weight (including Battery)
noise Power
noise Pressure
and therefore requires no earth cable.
²
²
²
²
CP3014vHK
14.4V - 1.7Ah
25mm
10mm
6.5mm
13mm (1/2")
25nm
cP3014VHKBP
2.4kg
81.9dB.A
92.9dB.A
Original Language Version
CP3018vHK
18V - 1.7Ah
led battery display.
Press to check
battery charge state.
30nm
cP3018VHKBP
2.5kg
83.2dB.A
94.2dB.A
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RATING 3 AMP
3
1
5
6
2
8
7
Fig. 1
1. Keyless chuck
2. led Battery display
3. torque/hammer selector control ring
4. High/low speed switch
5. lock, reverse and forward switch
6. Power switch
7. 18V battery pack (two supplied)
8. Battery release button (one each side)
cP3014VHK, cP3018VHK
Issue: 5 - 11/01/12
Brown
Live
Wire
Cable
Restraint
4
fig.1
Advertisement
