Do you have a question about the SKY903WH and is the answer not in the manual?
Questions and answers
Stuart Baker
May 31, 2025
We have recently moved into a house that has a Skyfan DC ceiling fan and the light bulb needs changing we cannot find out how to change it , we would be grateful for any advice
Page 1
With LED (-L) model Images are for reference only and may vary slightly from actual product. Ceiling Fan Installation Manual Rev 1.3 MODELS: SKY903WH, SKY903WH-L, SKY903BL, SKY903BL-L SKY1203WH, SKY1203WH-L, SKY1203BL, SKY1203BL-L SKY1303WH, SKY1303WH-L, SKY1303BL, SKY1303BL-L, SKY1303TK, SKY1303TK-L SKY1503WH, SKY1503WH-L, SKY1503BL, SKY1503BL-L, SKY1503TK, SKY1503TK-L Thank you for purchasing this quality Ventair DC ceiling fan.
Page 2
SAFETY PRECAUTIONS SAFETY PRECAUTIONS SAFETY PRECAUTIONS WARNING: WARNING: SAFETY PRECAUTIONS FOR SAFE USE OF THIS FAN, AN ALL-POLE DISCONNECTION MUST BE FOR SAFE USE OF THIS FAN, AN ALL-POLE DISCONNECTION MUST BE INCORPORATED INTO THE FIXED WIRING INACCORDANCE WITH THE WIRING RULES. INCORPORATED INTO THE FIXED WIRING INACCORDANCE WITH THE WIRING RULES.
Page 3
BEFORE INSTALLATION BEFORE INSTALLATION BEFORE INSTALLATION Unpack the fan carefully and identify all parts. Please refer to Fig 1. Unpack the fan and carefully identify the parts. Please refer to Fig 1. Unpack the fan and carefully identify the parts. Please refer to Fig 1. Skyfan WITH LIGHT Skyfan WITHOUT LIGHT Fig 1.
Page 4
INSTALLATION INSTALLATION BEFORE INSTALLATION MOUNTING BRACKET MOUNTING BRACKET • The ceiling fan must be installed in a location so that the blades have a minimum 300mm spacing The ceiling fan must be installed in a location so that the blades have a minimum 300mm spacing •...
Fig 4 (show Fig 5 here • Complete the electrical connection at the mounting bracket terminal block. NOTE: Skyfan DC is a class 2 electrical product. (Refer to Fig 6.). • Connect fan to the receiver (can be done before or after sliding receiver into place).
Page 6
Below is an example / guide for the electrical installer for maintaining CLASS 2 wiring to the Skyfan DC’s terminal block. STEP 2. Prepare the Heat shrink tubes with the same length and place over the 20-30mm single sheath insulatio bare copper sticking out.
a. For fan models “without light”, plug ‘AC IN b. For fan models “with light”, plug ‘AC INP 7.2) Slide the canopy upwards into position over • FINISHING THE INSTALLATION lock into position. Ensure all 4 Tabs on the After completing the electrical connection at the mounting bracket terminal block, connect the ceiling •...
REMOTE CONTROL OPERATION Fan Models Without Light 1. Turn wall switch to ‘ON’ Fan is now in standby mode. A ‘beep’ will be heard. Fan ‘ON’ and ‘OFF’ If your fan has a light, the light will illuminate in default setting Forward - downdraft for cooling (summer mode) Reverse - updraft for heat circulation (winter mode) of 100% brightness in (NW)
Page 9
The Skyfan DC remote control comes pre-paired at the factory and is ready to use. Pairing will only be required in situations mentioned below. 1. Using 1 remote handset to control 2 or more Skyfan DC Ceiling fans • Choose the fan you wish to pair with your handset.
Higher wattage, heavier AC type ceiling fan motors. The Skyfan DC Range are one of the quietest fans available and are ideal for all areas of the home especially bedrooms where noise is a crucial consideration.
WARRANTY INFORMATION • If you consider there are faults relating to the installation, contact your installer to rectify. • If you consider there is a manufacturer defect to the fan motor, contact the warranty service line on 1300 665 926, or submit a warranty claim at www.ventair.
Need help?
Do you have a question about the SKY903WH and is the answer not in the manual?
Questions and answers
We have recently moved into a house that has a Skyfan DC ceiling fan and the light bulb needs changing we cannot find out how to change it , we would be grateful for any advice