Download Print this page

Tuft & Needle 100-Night Trial Care & Assembly Instructions

Nook nightstand

Advertisement

Quick Links

Nook
Nightstand
Care & Assembly Instructions
Limited Warranty
100-Night Trial
201019_Nightstand_Assembly_Instructions_v8_jc.indd 1
201019_Nightstand_Assembly_Instructions_v8_jc.indd 1
10/23/20 9:30 PM
10/23/20 9:30 PM

Advertisement

loading
Need help?

Need help?

Do you have a question about the 100-Night Trial and is the answer not in the manual?

Questions and answers

Summary of Contents for Tuft & Needle 100-Night Trial

  • Page 1 Nook Nightstand Care & Assembly Instructions Limited Warranty 100-Night Trial 201019_Nightstand_Assembly_Instructions_v8_jc.indd 1 201019_Nightstand_Assembly_Instructions_v8_jc.indd 1 10/23/20 9:30 PM 10/23/20 9:30 PM...
  • Page 2 Thank you for your purchase. The handbook for your Nook. 201019_Nightstand_Assembly_Instructions_v8_jc.indd 2-3 201019_Nightstand_Assembly_Instructions_v8_jc.indd 2-3 10/23/20 9:30 PM 10/23/20 9:30 PM...
  • Page 3 Contents Caring for your Nook Nightstand 100-Night Trial 12-Year Limited Warranty Parts & Hardware Assembly More from T&N 201019_Nightstand_Assembly_Instructions_v8_jc.indd 4-5 201019_Nightstand_Assembly_Instructions_v8_jc.indd 4-5 10/23/20 9:30 PM 10/23/20 9:30 PM...
  • Page 4 Nook Nightstand to your wall. Instructions on page 16. All products are carefully inspected prior invalidate the remainder of your 100-Night under our 100-Night Trial Policy that we of your nightstand. to shipment. Please carefully inspect your Trial.
  • Page 5 Parts Hardware Flat washer × 8 Spring washer × 8 Assembly tool Threaded bolt × 8 Tip Kit Warning See page 16. To reduce risk of tip-over: Install included Tip Kit. See page 16. ► Never allow children to stand, climb, or hang on this product. ►...
  • Page 6 Assembly Questions about assembly? Call us at (877) 842-2586 Unpack all components onto a soft surface, placing the drawer top upside down. Place one leg in a corner slot of the drawer top , aligning the holes. Keep foam band around drawer while All paper and cardboard packaging is recyclable.
  • Page 7 Questions about assembly? Call us at (877) 842-2586 Using the assembly tool , tighten the two bolts on each leg. Place one spring washer and then one flat washer on each threaded bolt Insert into aligned holes and gently tighten each bolt with your fingers.
  • Page 8 Questions about assembly? Call us at (877) 842-2586 Flip your Nook Nightstand over slowly, as the drawer may open while turning it over to the upright position. Twist leveling feet individually to adjust the height and eliminate any tipping. To remove the drawer, squeeze both handgrips beneath the drawer and pull out gently.
  • Page 9: Tools Needed

    Tip Kit Hardware Tools Needed Questions about assembly? Call us at (877) 842-2586 Steel anchor × 2 Braided cable Drywall anchor × 2 Drywall screw (long) × 2 Drawer screw (short) × 2 Drill Phillips screwdriver This hardware can be used to install directly into drywall with or without an available stud.
  • Page 10 Tip Kit Assembly Questions about assembly? Call us at (877) 842-2586 Place assembled nightstand where you’ll be anchoring it along a wall. Leave at least 12" between the wall and the nightstand while you work. Attach a steel anchor to the back of the drawer top using two short drawer screws and a Phillips screwdriver...
  • Page 11 Questions about assembly? Call us at (877) 842-2586 With the nightstand in position, place the second steel anchor on the wall at the same height as the steel anchor on the back of the nightstand, and mark Anchoring into drywall both holes on the wall using a pencil.
  • Page 12 Loop the braided cable through the steel anchor holes on the nightstand and the wall. Tighten the screw cap to secure and close the cable loop. Once your Tip Kit is installed, push your Nook Nightstand Make the bedroom your Wood Frame Queen - Oak $995...
  • Page 13 TN.C OM ® 201019_Nightstand_Assembly_Instructions_v8_jc.indd 24 201019_Nightstand_Assembly_Instructions_v8_jc.indd 24 10/23/20 9:30 PM 10/23/20 9:30 PM...