Advertisement
Quick Links
ControlVIEW Xtreme
Pan/Tilt/Zoom Enhanced Camera Control System
Introduction
The ControlVIEW Xtreme is the most advanced camera controller for automating
preset positioning. The ControlVIEW Xtreme controls up to four VISCA
compatible Pan-Tilt-Zoom (PTZ) cameras, and positions them to various preset
locations when triggered by external devices, such as TouchVIEW, MicVIEW,
AutoVIEW, and third-party gated microphone mixers.
Unpacking
Carefully remove the device and part of the packing material:
the
ControlVIEW
Set the unit on a flat, solid surface, unpack and identify the following parts:
• One Power Supply
Xtreme
• One Power cord
• Two 12-Position 5mm terminal connectors
• Two 2-Position 5mm terminal connectors
• Two Rack Ears
• Four Screws
• One IR Remote Control
• Two AAA Batteries
ControlVIEW
Front Panel
(1) LCD screen
(2) Menu Control
(3) Program button
(4) Camera Selection Buttons
(5) IR Window
Installation & User Guide
TM
Indicates system status.
Execute Menu options.
Toggles Program Mode.
Choose from one of four cameras.
IR Receiver for remote operation
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for VADDIO ControlVIEW Xtreme
Summary of Contents for VADDIO ControlVIEW Xtreme
- Page 1 ControlVIEW Xtreme Pan/Tilt/Zoom Enhanced Camera Control System Introduction The ControlVIEW Xtreme is the most advanced camera controller for automating preset positioning. The ControlVIEW Xtreme controls up to four VISCA compatible Pan-Tilt-Zoom (PTZ) cameras, and positions them to various preset locations when triggered by external devices, such as TouchVIEW, MicVIEW, AutoVIEW, and third-party gated microphone mixers.
- Page 2 Serial Connection to Camera(s). (10) RS-232 input Serial Connection from Control System. IR Remote Power Toggle Power for All Cameras Control and ControlVIEW Xtreme Program Toggle Program Mode Used for Recalling Presets, or Storing Presets when in Program Mode Zoom In...
- Page 3 Setup The standard setup consists of a ControlVIEW Xtreme and one, two, three, or four VISCA compatible PTZ cameras and an external triggering device. In this configuration, the system will provide up to four cameras with total of 72 preset positions.
- Page 4 Default Timer when setting the Default Preset. Default Timer This sets the period of time for users who wish the ControlVIEW Xtreme to go to a specific preset or switch to a different camera after a period of inactivity. The time period can be selected from 0-60 seconds.
- Page 5 Pan Speed For users who wish the ControlVIEW Xtreme to adjust the speed at which the system moves from Preset to Preset. This adjusts the pan speed. 1. Using the Menu Control buttons, Press UP or DOWN until the arrow, points to Pan Speed.
- Page 6 Reset This option is only used when the ControlVIEW Xtreme needs to reboot. Reboot the system when new cameras or triggering devices are connected or disconnected. 1. Using the Menu Control buttons, Press UP or DOWN until the arrow, points to Reset 2.
- Page 7 To use the ControlVIEW Xtreme with such devices, the RS 232 protocol must be set to 9600 bps and data bits, 8N1, no parity and no flow control.
- Page 8 Xtreme. • Check all serial connections of all cameras in the daisy chain. • Confirm that the ControlVIEW Xtreme is not in program mode. • Confirm that no triggering device is trying to hold the ControlVIEW Xtreme at a preset •...
-
Page 9: Appendix A, Controlview Xtreme Api Protocol
Erase all presets TiltSpeed xx Set Tilt Speed +-----------------------------------------------------------------------------+ In order to control the ControlVIEW Xtreme, the Active Serial mode must be ON. Control Codes are not case sensitive. All commands must terminate with a carriage return (CR). Command Description... -
Page 10: Clear All
Pan/Tilt keys on the IR remote. Erases all preset information. LEAR Directs the ControlVIEW Xtreme to send the menu shown above to host. Sending the PASS instruction followed by a CR then followed by a camera instruction passes the camera instruction to the camera. -
Page 11: Appendix B, Controlview Xtreme Port Pin Configuration
Appendix B, ControlVIEW Xtreme Port Pin Configuration (Rear view of ControlVIEW Xtreme) Presets 25-48 Preset 25 Preset 37 Preset 38 Preset 48 Preset 49 Preset 61 Preset 62 Preset 72 Presets 49-72... - Page 12 • Inclement weather • Severe vibration Declaration of Conformity In accordance with ISO/IEC Guide 22 and BS 7514: Manufacturer’s Name: Vaddio Manufacturer’s Address: 4800 Quebec Ave N New Hope, MN 55428 This product complies with the requirements of the EMC Directive 89/339/EEC.
- Page 13 – Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty. If the product is out of warranty, Vaddio will test than repair the product or products for the cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair.
Need help?
Do you have a question about the ControlVIEW Xtreme and is the answer not in the manual?
Questions and answers