Advertisement
Commissioning the Hand Held Remote Control JC121371
Installing the Controller JC121372
1.
Connect the 24VDC output from the non-dimmable driver to the input on the controller
using DC cable or the DC jack plug(not supplied) as illustrated in Fig.1.
2.
Connect the RGBW strip to the Controller output as illustrated in Fig.2.
Hand Held Remote Control pairing set up(Fig.3.)
1.
Press the Power
button on the Remote Control
2.
Turn on mains supply to selected group(zone)
3.
Press and hold "Zone" button
for 2 to 8 seconds
4.
Pairing is completed when the white LED's Flash 3 times
5.
Repeat steps 2, 3 and 4 to pair additional groups to zones
Note: The maximum number of hand held remotes that can be paired to a group of
controllers is two, to pair the second hand held remote, repeat steps 1 through to 5
Hand Held Remote Control Reset(Fig.3.)
1.
Press the power
button on the Remote Control
2.
Turn on mains supply to selected group(zone)
3.
Press and hold selected "Zone" button
4.
Unpairing is completed when the white LED's Flash 9 times
5.
Repeat steps 2, 3 and 4 to unpair additional groups to zones
Scene setting -Dynamic mode
1.
Press the power
button on the Touch Control
2.
Selected zone button
3.
Press Dynamic mode button
to select preferred scene
(10 options see Fig.4.)
4.
Press
or
to adjust speed of selected scene
5.
Repeat steps 2, 3 and 4 to set scenes for zones
(note: brightness is not adjustable in dynamic mode)
Number
Mode
1
RGB jumping change
2
RGB fade in/out
3
7 colour jumping change
4
7 colour strobe
5
White fade in/out
6
Red fade in/out + flash 3 times
7
Green fade in/out + flash 3 times
8
Blue fade in/out + flash 3 times
9
White fade in/out + flash 3 times
10
Automatic cycle
JCC Lighting Products Ltd.
Innovation Centre
To fit battery ( 1 x 3V CR2032 not supplied), remove the cover on the back of the control, fit battery and then refit cover.
for 2 to 8 seconds
and
and
Fig.4.
Colour wheel
Power button
Dynamic mode
Zone 1 button
Zone 2 button
Beeding Close
Southern Cross Trading Estate
Scene setting -manual selection colours
1.
Press the power
button on the Remote Control
2.
Selected zone
button
3.
Touch colour wheel to select preferred colour
4.
Touch to adjust brightness press
5.
Repeat steps 2, 3 and 4 to set scenes for zones
(note: speed is not adjustable in this mode)
Scene setting - manual selection
1.
Press the power
button on the Remote Control
2.
Selected zone
button
3.
Press
button once will select RGB and white LEDs together
4.
Press
button again to turn off white LED's
5.
Press
button and hold for 1 sec to turn off RGB and turn on white LEDs
6.
Press
or
to adjust brightness
7.
Repeat steps 2, 3 and 4 to set scenes for zones
(note: speed is not adjustable in this mode)
Fig.1.
- +
DC Power input
DC Power input port 1
port 2(Cable)
(jack plug-not supplied)
Fig.3.
Speed/Brighness +
Speed/Brighness -
Zone 3 button
"W" function button
Bognor Regis
West Sussex
PO22 9TS
or
button
button
Fig.2.
RGBW connection Key:
V+=(Black)
R =(RED)
V+ R G B W
G =(GREEN)
B =(BLUE)
W=(WHITE)
RGBW output
connections
Controller dimensions
Remote Control dimensions
Technical Support: 01243 838986
106.0
4.0
52.0
Customer Services: 01243 838999
Advertisement
