ABB HT846170 Operation Manual page 180

Operation Manual / A150-M58/68
Tables
Tables
Table 1: Definition of pictograms ............................... 9
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table 4: Weight of complete turbocharger unit .... 29
Table 5: Torque-controlled tightening of the pres-
sure screws ................................................................... 36
Table 6: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 43
Table 7: Lubricating oil temperature at the inlet ... 44
Table 8: Maximum lubricating oil temperature at the
outlet .............................................................................. 44
Table 9: Tightening torque (86505).......................... 48
Table 10: Expected replacement intervals .............. 54
Table 11: Maintenance table ........................................ 57
Table 12: Parameters for wet cleaning of com-
pressor ........................................................................... 60
Table 13: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 63
Table 14: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 64
Table 15: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 65
Table 16: Value table for soaking ............................... 73
Table 17: Malfunctions when starting - Delayed
start-up .......................................................................... 76
Table 18: Malfunctions when starting - Vibrations 76
Table 19: Malfunctions when starting - Rubbing of
rotating parts................................................................ 76
Table 20: Malfunctions during operation - Lubricat-
ing oil pressure too low................................................ 77
Table 21: Malfunctions during operation - Speed re-
duces................................................................................ 77
Table 22: Malfunctions during operation - Speed in-
creases ............................................................................ 77
Table 23: Malfunctions during operation - Exhaust
gas temperature too high .......................................... 78
Table 24: Malfunctions during operation - Charge air
pressure too low........................................................... 78
© Copyright 2021 ABB. All rights reserved.
Table 25: Malfunctions during operation - Charge air
pressure too high .......................................................... 79
Table 26: Malfunctions during operation - Engine
performance losses....................................................... 79
Table 27: Malfunction - Turbocharger pumping ..... 80
Table 28: Malfunction - Sporadic surge blows ........ 80
Table 29: Malfunctions when stopping - Runout
noises ............................................................................... 81
Table 30: Malfunctions when stopping - Runout
time too short ................................................................ 81
Table 31: Malfunction of the speed measurement
system - No signal or poor signal amplitude .......... 82
Table 32: Malfunction of the speed measurement
system - Measured speed too high ........................... 82
Table 33: Malfunction of the speed measurement
system - Measured speed too low............................. 82
Table 34: Swivel lifting eyes......................................... 84
Table 35: Press-off screws ........................................... 85
Table 36: Dismantling screw ....................................... 85
Table 37: Weights of assemblies ................................ 90
Table 38: Tightening torques ...................................... 91
Table 39: Tightening torques for insulation ............ 92
Table 40: Press-off screws - gas outlet flange........ 97
Table 41: Tightening torque (90012-01) .................. 101
Table 42: Permissible clearances A and B ............... 106
Table 43: Nozzle ring compression PD .................... 107
Table 44: Tightening torque (90012-01) ................. 110
Table 45: Tightening torque (51007) ........................ 111
Table 46: Tightening torque (79041) ........................ 112
Table 47: Tightening torque (72011) ........................ 113
Table 48: Permissible clearances N and R................ 116
Table 49: Tightening torque (51009)........................ 119
Table 50: Tightening torque (51009)....................... 120
Table 51: Tightening torque (72051) ........................ 122
Table 52: Permissible clearances A and B ............... 130
Table 53: Nozzle ring compression PD ..................... 131
HZTL4041_EN Revision E January 2021