Advertisement
1903KITINT18_230 – 1903KITINT18_400 (E121001A_ENG)
26/10/2012
INSTRUCTION
INSTALLATION OF A REVERSING DRUM KIT
LINE "T" 10/14/18
FROM SERIAL NUMBER E201003027 (*)
(*) EACH TUMBLE DRYER HAVING A PRODUCTION CODE STARTING WITH T10.../T14.../T18...
ELECTRONIC BOARD "GICAR – IM7"
ELECTROMECHANIC "ABB"
IMESA S.p.A.
Via degli Olmi 22
31040 Cessalto (TV), Italia
tel. +39.0421.468011
fax +39.0421.468000
www.imesa.it
1
Advertisement
Related Manuals for Imesa ES10
Summary of Contents for Imesa ES10
- Page 1 LINE “T” 10/14/18 FROM SERIAL NUMBER E201003027 (*) (*) EACH TUMBLE DRYER HAVING A PRODUCTION CODE STARTING WITH T10…/T14…/T18… ELECTRONIC BOARD “GICAR – IM7” ELECTROMECHANIC “ABB” IMESA S.p.A. Via degli Olmi 22 31040 Cessalto (TV), Italia tel. +39.0421.468011 fax +39.0421.468000...
-
Page 2: Table Of Contents
1. INTRODUCTION Thi kit can be installed only on tumble Diagram and technical data may be dryers model ES10/14/18 which are not modified without any previous notice. yet equipped with the reversing drum option. -
Page 3: Manufacturer Liability
- 3,1A, 1NC+1NA Machine use contrary to the EU rules **2950RETT161V3 THERMAL RELAY T16 1A - (kit _400) 1,3A, 1NC+1NA in matter of safety and accident ES10/34 REVERSING 197848D prevent. MOTOR SUPPORT Not correct machine installation. PULLEY SPA 67x1 FORO 2080308X... - Page 4 1903KITINT18_230 – 1903KITINT18_400 (E121001A_ENG) 26/10/2012 h) Lower the motor support group to tension the A48 belt and to find the correct double pulley working position. i) Tighten the two pulley fixing bolts. j) Tighten the four motor support group fixing bolts. k) Remove the A48 belt.
-
Page 5: Installation - Mechanic
1903KITINT18_230 – 1903KITINT18_400 (E121001A_ENG) 26/10/2012 using some LOCTITE 243 to stop the threads. o) Control the four motor bolts correct tightness. p) If necessary, lower the motor support group few millimeters to reach the correct belt tension. INSTALLATION – MECHANIC Apply a closing force of 40 Nm on each COMPONENTS FOR SERIAL NUMBER bolts for fixing firmly the motor’s support. -
Page 6: Working Test
1903KITINT18_230 – 1903KITINT18_400 (E121001A_ENG) 26/10/2012 7. WORKING TEST Each single contactor can be tested. Using a screwdriver, push the pin until the contact is completely closed. In this situation, check the correct sense of rotation and, if necessary, invert the two phase in output. - Page 7 1903KITINT18_230 – 1903KITINT18_400 (E121001A_ENG) 26/10/2012 9. ELECTRIC DIAGRAM The following electric diagram refer to the wiring code: T110609X. As reference, take the connector CO9 (9 poles white connector into the electric box). The number printed on the left of the cable is exactly the number printed along the wire.
- Page 8 1903KITINT18_230 – 1903KITINT18_400 (E121001A_ENG) 26/10/2012...