Sealey SSP80PAPR Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Charger indoor
instructions use only
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with
all electrical products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fi tted with the
correct fuse - see fuse rating in these instructions.
 DO NOT pull or carry the appliance by the power cable.
 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a fi rm grip on the plug.
 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualifi ed electrician.
1.1.4. This product is fi tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualifi ed electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
 DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualifi ed electrician.
1.2. GENERAL SAFETY
 Ensure all workshop safety rules, regulations and conditions are complied with when using this equipment. The face shield will
not off er protection against misuse of workshop tools, equipment, or accessories.
 Maintain the face shield in good condition and protect cartridge from liquid and dirt contact.
 Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Fit the face shield and adjust the head band so the face shield will sit as low and near to your face as possible.
 Ensure that the face hood is securely attached to the face shield.
 Use face shield only in temperatures ranging from -5°C to 55°C.
 Remove ill fi tting clothing, remove ties, watches, rings and other loose jewellery.
 Maintain correct balance and footing.
 Ensure the fl oor is clear from obstructions, not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the working area.
 Use of this face shield is for face and eye protection against low energy impact and splashing liquids.
Inspect the face shield frequently as a pitted or scratched face shield reduces vision and therefore should be replaced immediately.

 Be aware if wearing standard ophthalmic spectacles they may transmit impacts, creating a hazard for the user.
 DO NOT use if any part of the face shield is cracked or broken.
 DO NOT place this product on a hot surface.
 DO NOT use this face shield for protection against gases, ultra violet or infra red radiation, ionising radiation, liquids under
pressure or other severe hazards.
 DO NOT use this face shield against heavy impact hazards, the lens is breakable.
 DO NOT use this face shield for welding or laser cutting.
 DO NOT use face shield for any purpose for which it is not designed.
 WARNING! DO NOT use the face shield if damaged or you suspect it may be faulty. (Contact Sealey Stockist).
© Jack Sealey Limited
DELUXE FACE SHIELD WITH POWERED AIR
PURIFYING RESPIRATOR (PAPR)
SSP80PAPR
MODEL NO:
Original Language Version
Recommended fuse rating
3 Amp
SSP80PAPR Issue 1 11/08/21