Hitachi CM827U User Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Monitor
  5. CM827U
  6. User manual

Hitachi CM827U User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
COLOR
(DJ82)
CM827U
EasyMenu
with
EasyMenu is HITCHI's On Screen Display function for easy operation.
READ
THE
KEEP THIS USER MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your color monitor.
SERIAL No.
The serial number is located on the rear of the monitor.
This monitor is E
NERGY
equipped with VESA DPMS.
®
The E
S
emblem does not represent EPA endorsement of
NERGY
TAR
any product or service.
®
As an E
S
NERGY
TAR
product meets the E
NERGY
MANUEL D'UTILISATION
!
INSTRUCTIONS
®
compliant when used with a computer
S
TAR
Partner, Hitachi,Ltd. has determined that this
®
guidelines for energy efficiency.
S
TAR
USER'S MANUAL
INSIDE
MONITOR
CAREFULLY.

Advertisement

Table of Contents
loading

Related Manuals for Hitachi CM827U

Summary of Contents for Hitachi CM827U

  • Page 1 VESA DPMS. ® The E emblem does not represent EPA endorsement of NERGY any product or service. ® As an E Partner, Hitachi,Ltd. has determined that this NERGY ® product meets the E guidelines for energy efficiency. NERGY...
  • Page 2 1/31/01 or 36 months for both panel and backlight if purchased after 1/31/01 . In the event of a defect during this 12 month, 36 month or 60 month period, Hitachi America, Ltd. will, at its option, repair or replace the monitor at no charge except as set forth below.
  • Page 3 For additional information, please write to: Hitachi America, Ltd. 200 Lowder Brook Drive, Suite 2200, Westwood, MA 02090 NEVER open the monitor cabinet. If the monitor is not operating properly, contact Hitachi America Ltd. service center (Call 1-800-536-6721). DO NOT OPEN THE MONITOR HOUSING UNDER ANY CIRCUMSTANCES.
  • Page 4 Company is authorized to change, modify, extend terms manner whatsoever. Hitachi Canada Ltd. shall not be responsible for any damages or loss of any kind attributed to the product rendered defective during usage, or attributed to incompatibility problems of linked equipment including software.
  • Page 5 TCO’99 STATEMENT Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
  • Page 6 29 February, 2000 Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements...
  • Page 7 Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion of lead since no replacement has yet been developed. Bio-accumulative is defined as substances which accumulate within living organisms Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

  • Page 8: Table Of Contents

    Color Monitor (DJ82) CM827U USER’S MANUAL Congratulations on your selection of a HITACHI Color Monitor. Read the instructions inside carefully, and keep this user manual for future reference. NOTE: • The information in this manual is subject to change without notice.

  • Page 9: Features

    FEATURES This Color monitor provides the following features. Sharpest Focus and Highest Contrast Flat screen Enhanced Dot Pitch (EDP) CRT with anti-glare, dynamic focus circuit, dark glass and an INVAR shadow mask gives the sharpest focus and highest contrast to minimize eye fatigue.

  • Page 10: Cautions

    CAUTIONS Discontinue Use if Abnormal Operation Occurs ! Abnormal operations such as smoke, burning smell, excessive sound, etc. could cause fire or electrical shock. If you observe any abnormal operation, you should turn off the monitor and disconnect the power plug from the power outlet. You should check for smoke or fire and contact your dealer.
  • Page 11 CAUTIONS (Continued) CAUTION (for 200 - 240V operation only) This equipment relies on the protective devices in the building installation for short-circuit and power surge protection. Refer to the following table for the suitable number and location of the protective devices which should be present in the building’s installation. Informative examples of protective devices in single - phase equipment or sub- assemblies Protection...
  • Page 12 CAUTIONS (Continued) FCC Statement Warning WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 13 1 - 6...
  • Page 14 CAUTIONS (Continued) For the Customers in the UK THIS PRODUCT IS SUPPLIED WITH A 2-PIN MAINS PLUG FOR USE ON MAINLAND EUROPE. FOR THE UK PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a molded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.

  • Page 15: Installation

    INSTALLATION Before installing, carefully read the chapter “CAUTIONS”. Checking the contents Check whether the consignment agrees with the following packing list. Should you discover that the equipment has been damaged during transport, or that the consignment does not correspond with the delivery list, please notify your dealer immediately. Delivery Note: one Monitor one Power Cord one Signal Cable...
  • Page 16 INSTALLATION (Continued) Connecting the monitor to the power outlet of the correct voltage Rear View to the host computer Front View 1. Installation Install the monitor in a suitable environment. Do not place the monitor on an unstable base. Do not expose the monitor to rain, moisture, dust, corrosive gases, vibrations, etc. so as to prevent electrical shock or fire hazard.

  • Page 17: Operation

    OPERATION Power ON/OFF Press the power switch to switch the power ON or OFF. When the power is ON, the power indicator will light up. NOTE: • First turn on the monitor, then the computer. • After turning OFF the power switch, wait at least 5 seconds before restarting the monitor.
  • Page 18 Brightness/Contrast Adjustment (1) Press one of the adjustment buttons when the OSD (On Screen Display) is not shown. The OSD function “EasyMenu” will then show the brightness and contrast settings. (2) To adjust these settings, use the adjustment buttons for brightness, and for contrast.

  • Page 19: Table 1-1. Adjustment Table

    OPERATION (Continued) Table 1-1. Adjustment Table Item Adjustment Function button BRIGHTNESS decreases the picture’s brightness. increases the picture’s brightness. CONTRAST makes the picture’s contrast darker (not including the background). makes the picture’s contrast brighter (not including the background). MAIN MENU change to the previous mode.
  • Page 20 OPERATION (Continued) Table 1-1. Adjustment Table (Continued) Item Adjustment Function button (MAIN MENU) TRAPEZOID shrinks the top side of the picture, and expands the bottom side of the picture. expands the top side of the picture, and shrinks the bottom side of the picture.
  • Page 21 OPERATION (Continued) Table 1-1. Adjustment Table (Continued) Item Adjustment Function button (MAIN MENU) OSD EXIT (no function) clears the OSD. (YES) ZOOM shrinks the picture horizontally and vertically. expands the picture horizontally and vertically. SCREEN MENU changes to the previous mode. H.
  • Page 22 OPERATION (Continued) Table 1-1. Adjustment Table (Continued) Item Adjustment Function button (SCREEN MENU) H. FOCUS makes the horizontal dynamic focus weaker. makes the horizontal dynamic focus stronger. V. FOCUS makes the vertical dynamic focus weaker. makes the vertical dynamic focus stronger. TOP CORNER curves the left and right top corners of the picture inwards.
  • Page 23 OPERATION (Continued) Table 1-1. Adjustment Table (Continued) Item Adjustment Function button OSD MENU changes to the previous mode. OSD H. POS. LANGUAGE SELECT OSD V. POS. OSD H. POS. changes to the next mode. OSD H. POS. OSD V. POS. LANGUAGE SELECT OSD H.

  • Page 24: Power Saving System

    POWER SAVING SYSTEM ® This monitor complies with VESA and E power saving requirements. NERGY The power saving system works only when used with VESA DPMS compliant PC’s and/or graphic controllers. Table 1-2. Power Saving System VESA DPMS Power Saving States Power Saving Video H.

  • Page 25: Troubleshooting

    TROUBLESHOOTING The following Table 1-4 is provided to assist you with common installation issues. Table 1-4. Troubleshooting Symptom Solution No power Verify that the power cord is installed correctly. Press the power switch. No picture Increase Contrast and Brightness. Check Input Select status. No picture and the power indicator Check the Signal Cable Connection.

  • Page 26: Specifications

    SPECIFICATIONS 21 inch type picture tube, 0.21mm horizontal dot pitch, 0.20 mm horizontal mask pitch, Invar shadow mask, Black matrix, Short persistence phosphors, Dark tint, Anti-Reflection coat. Input Signal Video 0.70 Vp-p, Analogue Sync. Separate H/V, TTL level Composite H/V, TTL level Synchronization Horizontal 31 - 107 kHz...

  • Page 27: Table 1-5. Standard Settings

    SPECIFICATIONS (Continued) Standard Settings Microprocessor-based user preset functions can store 32 sets of geometry settings. The following industrial standard settings have been pre- programmed by the factory. Table 1-5. Standard Settings Video Mode Name Horizontal Frequency (with Resolution and Vertical Frequency) 640 ×...

  • Page 28: Table 1-6. Pin Assignment

    SPECIFICATIONS (Continued) Pin Assignment Signal Input Connector of the Monitor Table 1-6. Pin Assignment Input 1 Input 2 Red Video Red Video Green Video Green Video Blue Video Blue Video No pin No pin No connection No connection Red Ground Red Ground Green Ground Green Ground...
  • Page 29 Technical Support : 1 - 800 - 536 - 6721 World Wide Web Home page : http://www.hitachidisplays.com In Canada : 1 - 800 - HITACHI or 905 - 821 - 4545 World Wide Web Home page : http://www.hitachi.ca All Rights Reserved Printed in CHINA.

Table of Contents