Table of Contents
Advertisement
Note
• The unit does not send out the output signal to DV
camcorder.
• For the proper operation, connect DV camcorder
to the unit directly. Do not connect this unit and
the DV camcorder via any other unit.
• Do not connect more than one DV camcorder.
• The unit can only accept DV camcorder. Other
DV equipment such as Set-top Box, or D-VHS VCR
cannot be recognised.
• Date / time and cassette memory data will not be
recorded.
• Pictures with a copy-guard signal cannot be
recorded.
• A DV terminal is a terminal that can use the
transmission mode conforming to the IEEE 1394
standards called "Fire Wire". It serves as the
interface that connects the PC and peripheral
equipment such as "i.Link" (registered trademark
of SONY). It enables digital dubbing between DV
devices with little degradation.
Before recording from DV
camcorder, see page 14 for
connection instructions.
Insert a recordable DVD-RW/-
R disc and make sure your DV
camcorder is in Playback mode.
VCR
DVD
Press
first.
1
2
3
4
5
6
7
8
9
0
+10
PLAY
STOP
VCR/DVD COMBINATION
NA527AD
1
Select "DV" using [PROG.
2
Select a recording mode using
[REC MODE]. (See page 24.)
3
Press [DISPLAY].
DV dubbing menu will appear.
1
1
0:00:00
Control
DVD
DV Audio
Stereo1
Start Rec
Downloaded from:
http://www.usersmanualguide.com/
Recording
DV dubbing (cont'd)
4
Press [ENTER] to display the
item selection. Select "DVC"
using [Cursor K / L], then press
[ENTER].
5
Press [PLAY B] to find the
point where you wish to begin
the dubbing.
Then, press [STOP C] at the
].
/
point you wish to start dub-
bing.
6
DV
AB-1234
Select "Start Rec" using [Cursor
0:00:00
K / L], then press [ENTER].
The dubbing will start.
To pause dubbing:
Select "Pause Rec" using [Cursor
K / L], then press [ENTER].
• DVC will pause the playback and
the unit will pause the dubbing.
7
Select "Control" using [Cursor
DVD-RW
K / L], then press [ENTER].
Video mode
DV
Select "DVD" using [Cursor
AB-1234
K / L], then press [ENTER].
0:00:00
Press [STOP C] to stop dubbing.
• You cannot dub from DVC to both DVD and VCR
format at the same time.
• You cannot change the output mode during DVC
to VCR dubbing. If you want to switch to the DVD
mode, stop the VCR first.
• During DVC to VCR dubbing, you cannot change
channels while paused.
• When the output is in DVD mode while playing
back a DVD using AV4 (DV-IN), you cannot switch
to the VCR mode.
• If you are using anything other than AV4 (DV-
IN) to playback DVD, you can switch to the VCR
mode, but cannot select AV4 (DV-IN) channel.
(You can select AV4 (DV-IN) after switching to the
DVD mode during VCR playback.)
• You cannot dub from DVC during timer standby
mode.
• During timer standby of either component,
you cannot select AV4 (DV-IN) even on the
component which is not in timer standby.
2
1
3
Note
• To avoid unrecorded part, the
tape will rewind to the point
a few seconds preceding the
paused point if you select
Rec" whenever the DVC is in
pause mode
• If no video signal is detected
from the DV camcorder during
DVC to DVD dubbing, the
recording will be paused and
"I" will flash on the screen.
The recording will resume
when the unit detects a video
signal again.
• When the DV camcorder is in
Camera mode, refer to "Guide
to DV and On-Screen Display"
on page 36.
T-SET TIMER PROG.
REC MODE
RAPID PLAY
VCR
DVD
ZOOM
CM SKIP
4
TOP MENU
MENU LIST
6
ENTER
RETURN
.@/:
ABC
DEF
7
1
2
3
PROG.
GHI
JKL
MNO
6
4
5
PQRS
TUV
WXYZ
7
8
9
SKIP
CLEAR/C-RESET
SPACE
DISPLAY
0
REV
FWD
PLAY
5
VCR
DVD
REC/OTR
REC/OTR
STOP
7
"Start
.
EN
37
Advertisement
Table of Contents
