Page 1
Part #501126-001 Product Manual: Model #BC-08A Adjustable Angle Beam Clamp IS O 9 0 0 1 Certified T.A. Pelsue Company 2500 South Tejon Street Englewood, Colorado, USA 80110 Tel. 800-525-8460 or 303-936-7432 Fax. 303-934-5581 Internet: www.pelsue.com Email: sales@pelsue.com...
Page 3
Pelsue continues the dedication that industry throughout the world. has made us pre-eminent in this field. Page 3 #501126-001 - Product Manual: Model #BC-08A Adjustable Angle Beam Clamp - Revision 00 - Date: 12-03-2009...
EVERY T.A. PELSUE COMPANY EMPLOYEE IS ExPECTED TO COMMIT TO THIS PHILOSOPHY IN THE PERFORMANCE OF HIS OR HER DAILY TASkS. QUALITY FIRST! T.A. PELSUE COMPANY SENIOR MANAGEMENT TEAM Page 5 #501126-001 - Product Manual: Model #BC-08A Adjustable Angle Beam Clamp - Revision 00 - Date: 12-03-2009...
2.0 - Introduction & Product Information Congratulations on your choice of a Pelsue Model #BC-08A Adjustable Angle Beam Clamp to compliment your fall arrest system. This equipment has been designed and manufactured to exceed fall arrest requirements and regulations in order to meet the needs of the discriminating operator.
3.0 - Configuration & Assembly Upon initial receipt of the #BC-08A system, inspect the packaging for any evidence that the product may have been damaged in shipment. While unpacking the product, inspect all of the components for damage. If damage to any of the components is discovered, DO NOT USE THE PRODUCT! Alert the shipping carrier immediately of the damage to the shipment.
4.0 - Safety The following section will address the safety precautions which must be adhered to when working with Pelsue Fall Arrest equipment such as the #BC-08A Adjustable Angle Beam Clamp. Any user must familiarize themselves with the informa- tion in this section before utilizing the equipment.
Securely anchor the product before using. Use only certified anchor and connector components in your system. Use only an approved full body harness for the workers. Page 10 #501126-001 - Product Manual: Model #BC-08A Adjustable Angle Beam Clamp - Revision 00 - Date: 12-03-2009...
4.6 - New Operator or Owner The Pelsue #BC-08A Adjustable Angle Beam Clamp is designed as a portable Base System for a Pelsue Model #FT- C70 fall arrest tower. Every new operator must read, understand and follow the instructions in this Product Manual. No person should be permitted to use the equipment without prior proper training.
Pelsue Model #FT-C70 Fall Arrest Tower. All specifications, instructions, and procedures provided within this manual or upon Pelsue Specification Documents are based upon and only valid for usage with a Pelsue #FT-C70 Fall Arrest Tower. The T.A. Pelsue Company can not verify equipment safety and/or compliance when utilized with anything other than Pelsue- approved BC-08A complementary products.
Loading Diagram: Fall Arrest Tower Mounting via Base Lugs Top Mount Edge Mount 5.2 - Product Installation & Set-up Prior to Operation, the #BC-08A Adjustable Angle Beam Clamp must be configured and installed according to the fol- lowing guidelines. Base Track Teeth Lugs Tightening Nuts 1.
Page 15
Place the fall arrest tower onto the #BC-08A, center the base of the tower between the base lugs present on the angle beam clamp (Refer to Fig. 5.2f). d. Align the holes of the fall arrest tower base with the holes of the base lugs on the #BC-08A and replace the tower’s retaining pin (Refer to Fig. 5.2g).
6.1 - Maintenance For the most part, the Model #BC-08A is intended to be a maintenance-free piece of equipment, however several steps can be taken to keep the system in top-notch working order and also extend the working life of the product.
Page 17
Doing so will make it possible to disassemble the plates so that they can be thoroughly cleaned. Clean or wipe away and dirt or debris that could cause improper meshing of the track teeth. Page 17 #501126-001 - Product Manual: Model #BC-08A Adjustable Angle Beam Clamp - Revision 00 - Date: 12-03-2009...