Advertisement
Quick Links
In case of inconsistencies or conflicts between the English version and any other versions of this manual (or
document), the English version shall prevail and take control in all respects.
For the latest Europe, Asia, Australia, Latin America and Africa please refer to
NEW REVISION: X
Safety and Installation Instructions
for Europe, Asia, Australia, Latin America and Africa
This document applies to Maxeon PV Modules
Contents of this manual are subject to change without notice.
www.sunpower.maxeon.com/int/PVInstallGuideIEC
Maxeon Solar Technologies, Ltd.
www.sunpower.maxeon.com
Languages:
English
French
German
Italian
Japanese
Spanish
Polish
Document 001‐15497 Rev X
P/N 100657
P/N 520728
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Maxeon Sunpower E Series
Summary of Contents for Maxeon Sunpower E Series
- Page 1 NEW REVISION: X Safety and Installation Instructions for Europe, Asia, Australia, Latin America and Africa This document applies to Maxeon PV Modules Languages: English French German Italian Japanese Spanish Polish Contents of this manual are subject to change without notice. In case of inconsistencies or conflicts between the English version and any other versions of this manual (or document), the English version shall prevail and take control in all respects. For the latest Europe, Asia, Australia, Latin America and Africa please refer to www.sunpower.maxeon.com/int/PVInstallGuideIEC ...
- Page 2 Do not allow the connectors to come in contact with chemicals only. such as greases, oils and organic solvents which may cause stress cracking. 1.3 Limited Warranty Do not install or handle the modules when they are wet or during Module limited warranties are described in the Maxeon warranty periods of high wind. document obtainable at www.sunpower.maxeon.com. Please read Do not block drain holes or allow water to pool in or near module this document for more information. frames Warranties do not apply to any of the following; ...
- Page 3 Module Mounting should be determined by the applicable codes. We recommend a size not less than 4mm . The insulation type should be appropriate for the The Maxeon Limited Warranty for PV Modules is contingent upon type of installation method used and must meet SCII (Safety Class II) modules being mounted in accordance with the requirements and IEC 61730 requirements. To minimize the risk from indirect described in this section. lightning strikes (Voltage surges), the system should be designed to avoid loops in the wiring. ...
- Page 4 Warranty for these modules. module and reduce the strength of the frame, therefore are not No Maxeon module should be mounted at a site where it may be allowed. Using mounting Clamps or clips with additional grounding subject to direct contact with salt water, or other aggressive ...
- Page 5 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Maxeon specified or Maxeon supplied mounting systems. Modules mounted with strict adherence to Maxeon Figure 3: Mounting Configurations documentation, using hardware systems supplied by or specified by Maxeon. Figure 2 and Table 1.1 below demonstrate the mounting locations and Tables 1.2 and 1.3 give allowed load ratings (designed test value) for Maxeon modules. Figure 2: Mounting Zone locations for Maxeon modules Configurations 1 and 2 show mounting with rail support, 3 and 4 show mounting without rail support. In “With Rail Support” the rails For P‐Series, MAX3 96, 104, 112 cells and MAX6 66 cells: becomes conventional or rails transverse while “Without Rail Support” becomes end mounted in long or short side. In the case when the glass deflects it would not deflect in the rails for additional support. ...
- Page 6 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Table 1.3: Mounting Zone Load Ratings for Racking system with rail Figure 4: Mounting Zone Locations for Performance modules support. Refer to Configuration 1 and 2 in Fig.3 Wind (up & down) / For P3, P5 UPP and P6 (COM‐M, COM‐S, RES BLK) Module Configuration Snow (down) (units in Pa) (***) Module size Frame type B C (1&2&3&4) (1&2&3&4) G3 (Black &Silver) & 96 cells and P3 BLK 2400 / 5400 G4.1 & G4.2 2400 / 2400 104 cells (MAX2, MAX3) and 112‐cells G4.2 3600/5400 (MAX3) P3 RES+ G4.3 1600/3600 1600/3600 128 cells and P19‐COM G4 & G4.1 & G4.2 3600 / 5400 2400/ 3600 P3‐COM G4.2 & G4.3 2000/2400 1600/2400 ...
- Page 7 During storage, modules need to be protected from rain or any kinds of liquids. Required storage temperature is between 10°C to 40°C in a dry environment (humidity between 30 to 80%). Do not store modules outdoor to avoid moisture and wet conditions. Modules that feature antireflective coated glass are prone to visible finger print marks if touched on the front glass surface. Maxeon recommends handing modules with anti‐reflective glass with gloves (no leather gloves) or limiting touching of the front surface. Any finger print marks resulting from installation will naturally disappear over time or can be reduced by following the washing guidelines in Section 6.0 below. Any module coverage (colored plastic tarps or similar) during installation can lead to permanent front glass discoloration and ...
- Page 8 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Table 2: Module Frame Details Platform Module mounting and ground hole detail Frame Profile RESIDENTIAL G3 FRAME ONLY 96 CELL MODULE FRAME DETAIL SIDE FRAME PROFILE 10.30 mm 46.08 mm 18.50 mm 2.20 mm Residential 32 mm Modules END FRAME PROFILE 10.50 mm Method 1: Frame Hole 46.08 mm Locations 1.27 mm 22 mm FOR COMMERCIAL (SILVER FRAME) MODULES ONLY, INCLUDES STACKING PINS ...
- Page 9 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Platform Module mounting and ground hole detail Frame Profile FOR P‐SERIES COMMERCIAL GEN 4.1 FRAME MODULES SIDE FRAME PROFILE 2067 mm 46 mm 32mm Commercial Modules END FRAME PROFILE 4X Ø 4.2mm 20X Ø 6.8mm 4X 5.0mm (W) x 15.0mm (L) Ground Holes Mounting Holes 24 mm SLOT ...
- Page 10 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Platform Module mounting and ground hole detail FOR P3 MODULES P3 BLK (GEN 4.3) P3 COM (GEN 4.2) 998 mm 998 mm 954 mm 954 mm Mounting Holes 4X Ø6.8mm Mounting Holes 12X Ø6.7mm 4X Ø4.2mm Ground Holes Mounting Holes 4X 5.0mm (W) 8X Ø6.8mm x 15.0mm (L) Residential/ SLOT Commercial ...
- Page 11 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Platform Module mounting and ground hole detail Frame Profile FOR P3 UPP GEN 4.3 ( Customized) 2066 mm SIDE FRAME PROFILE 2022 mm 274 mm Commercial 35 mm Modules END FRAME PROFILE 8X (14mmx9mm) 4X Ø4.2 mm 35 mm Mounting Holes Ground Holes FOR P5 UPP & P6 BIFACIAL GEN 4.3 SIDE FRAME PROFILE 2384 mm 1400 mm 1100 mm...
- Page 12 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Platform Module mounting and ground hole detail Frame Profile FOR P3 RES+ (GEN 4.3) SIDE FRAME PROFILE 1690 mm 1500 mm 1300 mm 1100 mm Residential 32 mm Modules END FRAME PROFILE 4X Ø 4.2mm 8X Ø 6.8 mm Ground Holes Moun ng Holes 24 mm FOR 112c GEN 4.2 FRAME MODULES ...
- Page 13 MAXEON SOLAR TECHNOLOGIES, LTD. Safety and Installation Instructions ‐ Document 001‐15497 Rev.X Platform Module mounting and ground hole detail Frame Profile FOR MAX6 72‐CELL GEN 5.6 FRAME MODULES 2047 mm SIDE FRAME PROFILE 1983 mm 1653 mm 1423 mm 1200 mm 35 mm 400 mm 35 mm 32 mm Commercial END FRAME PROFILE Modules 35 mm 96.50 mm 4X Ø 4.60mm 16X Ø 6.80 mm 4X Ø...
Need help?
Do you have a question about the Sunpower E Series and is the answer not in the manual?
Questions and answers