Advertisement

Operator's
PAS-225/225SB/
225VP/225VPB
Pro Attachment
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth defects,
or other reproductive harm.
Read and understand all provided literature before
use. Failure to do so could result in serious injury.
X7732274006
© 09/21 ECHO Incorporated
Manual
Series™

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PAS-225VP and is the answer not in the manual?

Questions and answers

Summary of Contents for Echo PAS-225VP

  • Page 1 The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Read and understand all provided literature before use. Failure to do so could result in serious injury. X7732274006 © 09/21 ECHO Incorporated...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Introduction......................... 3 Servicing Information....................3 Parts and Serial Number..................3 Service ....................... 4 ECHO Consumer Product Support ..............4 Product Registration................... 4 Additional Literature ................... 4 Safety ......................... 5 Manual Safety Symbols and Important Information ........... 5 International Symbols..................
  • Page 3: Introduction

    SERVICING INFORMATION Parts and Serial Number Genuine ECHO Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with you. For future reference write them in the space provided below.
  • Page 4: Service

    Register your ECHO equipment on-line at www.echo-usa.com or by filling out the product registration sheet included in this manual. Registering your product confirms warranty coverage and provides a direct link to ECHO if we find it necessary to contact you.
  • Page 5: Safety

    Note: This enclosed message provides tips for use, care and maintenance of the unit. CIRCLE AND SLASH SYMBOL This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury. X7732274006 © 09/21 ECHO Incorporated...
  • Page 6: International Symbols

    Keep Bystanders At Least 15 m (50 ft.) Away Beware Thrown Objects Wear Eye Protection Keep Bystanders and Helpers Away 15 m (50 ft.) DO NOT Allow Ignition Flames or Sparks ON / OFF Near Fuel X7732274006 © 09/21 ECHO Incorporated...
  • Page 7 Keep bystanders at falling objects. least 15 m(50 ft.) away. DO NOT USE Line DO NOT USE BLADES Head - blades Only - Line Head Only Note: Not all symbols will appear on your unit. X7732274006 © 09/21 ECHO Incorporated...
  • Page 8: Personal Condition And Safety Equipment

    Eye protection that meets ANSI Z87.1 or CE requirements ◆ must be worn whenever you operate the unit. For additional safety, a full-face shield can be worn over ◆ safety glasses or goggles to provide protection from sharp branches or flying debris. X7732274006 © 09/21 ECHO Incorporated...
  • Page 9 Gloves also provide protection against cuts and scratches, cold environments, and reduce the transmission of machine vibration to your hands. Hearing and Ear Protection ECHO recommends wearing personal protective equipment whenever unit is used. Breathing Protection Operators who are sensitive to dust or other common airborne allergens may need to wear a dust mask to prevent inhaling these materials while operating unit.
  • Page 10 In the absence of such information, ECHO does not recommend the use of this machine by anyone who has a pacemaker. Extended Operation and Extreme Conditions Prolonged exposure to cold and/or vibration can result in injury.
  • Page 11 Never touch wires directly or indirectly, otherwise serious injury or death can result. Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. X7732274006 © 09/21 ECHO Incorporated...
  • Page 12: Equipment

    Incorporated will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions. Do not attempt to modify this product. Serious injury can ◆...
  • Page 13 ◆ or other damage, and repair or replace as needed. Exposed wire or connectors can cause shocks, sparks, and risk of fire or explosion, resulting in serious injury. Check wire terminals for secure connections. ◆ X7732274006 © 09/21 ECHO Incorporated...
  • Page 14: Emission Control (Exhaust & Evaporative)

    The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. X7732274006 © 09/21 ECHO Incorporated...
  • Page 15: Description

    Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your ECHO dealer. Safety label is for example only. Your label my appear slightly different.
  • Page 16 22. Debris Shield with Cutoff Knife 23. Trimmer Driveshaft Assembly 24. Storage Hook 25. Blower Pipe 26. Blower Drive Shaft Assembly 27. Blade 28. Blade Guard 29. Edger Drive Shaft Assembly 30. Storage Hook 31. Wheel X7732274006 © 09/21 ECHO Incorporated...
  • Page 17: Contents

    Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. PAS-225/SB Power Head with Upper Drive Shaft Assembly...
  • Page 18: Assembly

    Note: Lower bearing housing and head assembly must be in line with the engine. Note: Some models have an assembly line decal to assist in assembly. X7732274006 © 09/21 ECHO Incorporated...
  • Page 19: Balance And Adjust Unit

    (8 in ± 4 in) from the ground. Tighten harness clamp screw. Loosen handle clamp screw(s), and position handle for comfortable operation. Tighten handle clamp screws 200 mm ± 100 mm securely. (8 in. ± 4 in.) X7732274006 © 09/21 ECHO Incorporated...
  • Page 20: Operation

    Fuel Diesel fuels and alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of diesel or alternative fuels can cause performance...
  • Page 21 NOT approved. Use of ECHO branded fuel is recommended to extend engine life in all air-cooled 2-stroke and 2/4-stroke hybrid engines. Two Stroke Oil - A two-stroke engine oil, such as ECHO branded 2-stroke oils, meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards must be used.
  • Page 22 Vapors ignited by an ignition source can flash back to the fuel container, resulting in an explosion, fire, serious or fatal injuries, and extensive property damage. X7732274006 © 09/21 ECHO Incorporated...
  • Page 23 • Empty the fuel tank prior to storing the unit. Return unused fuel to an approved fuel storage container. Stored two-stroke fuel can separate. ALWAYS shake fuel container thoroughly before each use. Used oil and gasoline, and soiled towels are hazardous waste materials. Disposal laws vary by locality. X7732274006 © 09/21 ECHO Incorporated...
  • Page 24: Operation With Blades

    U-Handle ensures a higher safety factor. Do Not install blades on GT (Curved Shaft) model trimmers. • Use only ECHO approved parts. Failure to use the correct parts can cause the blade to fly off. Seriously injury to the operator and / or bystanders can occur.
  • Page 25: Blade Selection

    13 mm (0.5 in.) diameter. 22-Tooth Clearing Blade is designed for dense thickets and saplings up to 64 mm (2.5 in.) diameter. A trimmer-brushcutter with a metal blade can cause serious injuries if handled improperly. X7732274006 © 09/21 ECHO Incorporated...
  • Page 26 Make sure the warning sign on the back of the shoulder harness can be read easily. Note: In case of Emergency, disconnect the trimmer from the harness. X7732274006 © 09/21 ECHO Incorporated...
  • Page 27: Starting Cold Engine

    Move choke lever (B) to COLD START ( ) position. Purge Bulb Pump purge bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. Recoil Starter X7732274006 © 09/21 ECHO Incorporated...
  • Page 28: Starting Warm Engine

    Note: If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. Stop Switch Move stop switch button (A) forward away from the STOP position. X7732274006 © 09/21 ECHO Incorporated...
  • Page 29: Stopping Engine

    Note: If engine does not start after 2-3 pulls, use Cold Start Procedure. Stopping Engine Throttle Release throttle trigger and allow engine to return to idle before shutting off engine. Stop Switch Move stop switch button (A) backward to STOP position. X7732274006 © 09/21 ECHO Incorporated...
  • Page 30: Applications

    PAS-225/SB/VP/VPB If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using unit again. Applications Do Not install blades on GT (Curved Shaft) trimmers.
  • Page 31: Operating Techniques - Metal Or Plastic Blade

    Suggested cutting width is about 1.5 m (4.9 ft). • When scything large brush up to 0.5" diameter from right to left, avoid cutting with highlighted section. X7732274006 © 09/21 ECHO Incorporated...
  • Page 32: Reaction Forces

    The reactive force is in the opposite direction of blade rotation at the contact point, regardless of where the contact is being made. These types of reactive forces are also called “Blade Thrust.” X7732274006 © 09/21 ECHO Incorporated...
  • Page 33: Blade Cutting Problems

    Use caution when releasing the tree to avoid being struck by spring-back or falling. X7732274006 © 09/21 ECHO Incorporated...
  • Page 34: Edger Operation Techniques

    Tighten adjustment knob (A). Before edging, plan your direction of travel so that the unit will always be positioned on your right side and so that you walk on a hard surface 0.5 in. (13 mm) whenever possible. X7732274006 © 09/21 ECHO Incorporated...
  • Page 35 Don't force the blade. Move only as quickly as the blade will allow. The complete unit, specifically the drive shaft assembly and muffler exhaust area may become very hot during use. Avoid contact during and immediately after operation, otherwise serious personal injury may result. X7732274006 © 09/21 ECHO Incorporated...
  • Page 36: Operating Blower

    Allow the engine to warm up at a fast idle for a few minutes. Use lower speed to blow debris from hard surfaces. Additional speed may be necessary to clean debris, snow, etc. from lawns and flowerbeds. X7732274006 © 09/21 ECHO Incorporated...
  • Page 37: Maintenance

    If the task is not listed, see your Dealer for repairs. The use of emission control components other than those specifically designed for this unit is a violation of federal law. X7732274006 © 09/21 ECHO Incorporated...
  • Page 38: Skill Levels

    Skill Levels Level 1 = Easy to do. Common tools may be required. Level 2 = Moderate difficulty. Some specialized tools may be required. Level 3 = See your dealer. Click HERE or go to http://www.echo-usa.com/products/maintenance-kit HERE https://www.shindaiwa-usa.com/you-can.aspx Maintenance Intervals REQUIRED...
  • Page 39: Air Filter

    • Soak heavily soiled filters in water/detergent solution to loosen dirt, then brush lightly. • Rinse with clean water and allow to dry completely before reuse. Install air filter in air filter case. Install air filter cover. X7732274006 © 09/21 ECHO Incorporated...
  • Page 40: Fuel Filter

    2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500 may be enforced for using a non-certified replacement part. X7732274006 © 09/21 ECHO Incorporated...
  • Page 41: Spark Plug

    • Air intakes are blocked, preventing cooling air from reaching the cylinder. • Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving. X7732274006 © 09/21 ECHO Incorporated...
  • Page 42 Use a brush to remove dirt from the cylinder fins. Remove ignition wires from clip for cleaning. Remove grass and leaves from the grid between the recoil starter and fuel tank. Assemble components in reverse order. X7732274006 © 09/21 ECHO Incorporated...
  • Page 43: Exhaust System

    Exhaust Port Cleaning Level 2. Parts Required: As needed: Heat Shield Remove spark plug lead from spark plug, and remove engine cover. Place piston at top dead center. Remove muffler (A) and heat shield (B). X7732274006 © 09/21 ECHO Incorporated...
  • Page 44: Carburetor Adjustment

    330 m (1100 ft.) above sea level (ASL). To maintain proper engine operation and emission compliance above 330 m (1100 ft.) ASL the carburetor may need to be adjusted by an authorized dealer. X7732274006 © 09/21 ECHO Incorporated...
  • Page 45 “Specifications” page of this manual. Turn idle screw (A) clockwise to increase idle speed; counterclockwise to decrease idle speed. When carburetor adjustment is completed, the cutting attachment should not move at idle, otherwise serious personal injury may result. X7732274006 © 09/21 ECHO Incorporated...
  • Page 46: Lubrication

    Slide coupler on upper drive shaft until fully seated, and align set screw hole in coupling with hole in upper drive shaft. Install and tighten set screw (D), and tighten clamping screw (C). X7732274006 © 09/21 ECHO Incorporated...
  • Page 47: Lubrication

    Loosen screw (B) and remove locating screw (C). Pull gear case and shield from drive shaft housing. Pull flexible cable (D) from the drive shaft housing, wipe clean and re-coat with 15 ml (0.5 oz.) of grease. X7732274006 © 09/21 ECHO Incorporated...
  • Page 48: Nylon Line Head Disassembly Instructions

    However, if circumstances require disassembly, follow these instructions. Press top of locking tabs (A) on ® both sides of Speed Feed head to release cover (B) from eyelet carrier (C). Remove cover from eyelet carrier. X7732274006 © 09/21 ECHO Incorporated...
  • Page 49: Nylon Line Replacement

    2.4 mm (0.095 in.) diameter 6 m (20 ft.). Align arrows on top of knob with openings in eyelets. Insert one end of trimmer line into an eyelet, and push line equal distance through trimmer head. X7732274006 © 09/21 ECHO Incorporated...
  • Page 50 When the wear indicators located at the bottom of the ® Speed-Feed head are worn smooth, or if holes appear, replacement of the cover or the ® entire Speed-Feed head required. X7732274006 © 09/21 ECHO Incorporated...
  • Page 51: Sharpening Metal Blades

    If an electric grinder is used, use care not to overheat teeth, do not allow tips/tooth to glow red or turn blue. DO NOT place blade in cooling water. This will change the temper of the blade and could result in blade failure. X7732274006 © 09/21 ECHO Incorporated...
  • Page 52: Lubrication

    Add grease if necessary using squeeze-type tube. Do not use high pressure grease gun. DO NOT over-fill. Drive Shaft (Lower) Loosen screw (A) and remove center locating screw (B). Pull gear box and shield from drive shaft housing. X7732274006 © 09/21 ECHO Incorporated...
  • Page 53: Edger Blade Replacement

    Remove L.H. blade nut (D) by turning clockwise. Remove outer blade adapter (E), and blade (F). Install and center blade (F) on inner blade adapter (B). Install outer adapter (E) and nut (D). Tighten nut (D) firmly, turning counterclockwise. X7732274006 © 09/21 ECHO Incorporated...
  • Page 54: Troubleshooting

    Clean or replace runs, but Fuel filter Contaminants Replace filter or dies Fuel filter dirty or residue in fuel replace fuel Engine Fuel vent Contaminated Fuel vent Clean or replace does not plugged fuel accelerate properly X7732274006 © 09/21 ECHO Incorporated...
  • Page 55 See your dealer problem crank Fuel vapors are extremely flammable and can cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury can result. X7732274006 © 09/21 ECHO Incorporated...
  • Page 56: Storage

    Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there. 10. Install the spark plug. Connect the spark plug lead to the spark plug. X7732274006 © 09/21 ECHO Incorporated...
  • Page 57: Pas-225 Sb Only

    Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio 50:1 Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% Gasoline MTBE. Do not use alternative fuels such as E-15 or E-85. X7732274006 © 09/21 ECHO Incorporated...
  • Page 58 Drive Shaft (upper & lower) 6.35 mm (0.25 in.) flexible shaft Rotating Direction Counterclockwise; viewed from top ® Speed Feed Nylon line head, Line capacity 6.0 m Trimmer Attachment (20 ft.) Handles Front - Support, Rear Handle (with rubber) X7732274006 © 09/21 ECHO Incorporated...
  • Page 59 Maximum Air Volume 347 - 383 ft /min. * Sound Level at 50 ft. dB(A) scale per 71 dB(A) ANSI B175.2 * Specifications are for a variety of power heads. Individual unit performance may vary. X7732274006 © 09/21 ECHO Incorporated...
  • Page 60: Echo Optional Attachments

    Read and comply with all safety instructions listed in this manual and attachment manual. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO for use with these units.
  • Page 61 PAS-225/SB/VP/VPB PRODUCT REGISTRATION X7732274006 © 09/21 ECHO Incorporated...
  • Page 62 NOTES PAS-225/SB/VP/VPB NOTES X7732274006 © 09/21 ECHO Incorporated...
  • Page 63 PAS-225/SB/VP/VPB NOTES NOTES X7732274006 © 09/21 ECHO Incorporated...
  • Page 64 T99814001001 - T99814999999 U36314001001 - U36314999999 U45714001001 - U45714999999 U54914001001 - U54914999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.com...

This manual is also suitable for:

Pas-225Pas-225sbPro attachment seriesPas-225vpb

Table of Contents