Bosch PFS 1000 Original Instructions Manual page 22

22 | English
Air cap Spray jet pattern Application
Setting the spray material quantity (see figure G)
(PAINTVolume)
– Turn the thumbwheel (5) to set the required spraying ca-
pacity:
−: Minimum quantity of spraying material,
+: Maximum quantity of spraying material.
– Start with a spray test with the minimum spray material
volume and increase the volume until the required spray
pattern is achieved. If a satisfactory spray pattern is not
achieved, dilute the spray material in 5 % increments (see
"Preparing the spray material", page 20).
Please note: The intensity of the paint application is highly
dependent on the moving speed.
Spray material Setting
volume
Too much mater- The spray material volume
ial on target area must be reduced.
– Turn the thumbwheel (5)
in direction –.
Not enough ma- The spray material volume
terial on target must be increased.
area
– Turn the thumbwheel (5)
in direction +.
Dampening Wallpaper
To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C). Use the grey
nozzle cap (9) to do so.
Work breaks and transport (see figure H–I)
A carrying handle (24) and a carrying strap (25) are fitted to
the base unit to enable easy transport of the fine-spray sys-
tem.
You can hang the base unit (22) across your shoulder during
work using the carrying strap (25).
The spray gun (1)can be put down on a flat work surface dur-
ing breaks. No spray material can leak out.
Always put the spray gun upright on a flat surface
u
when it is filled with spray material. Spray material can
leak out from a spray gun if it is lying down.
1 609 92A 687 | (16.09.2021)
Maintenance and Service
Vertical flat jet for
Maintenance and Cleaning
horizontal working
direction
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Round jet for
In order to avoid safety hazards, if the power supply cord
corners, edges and
needs to be replaced, this must be done by Bosch or by an
hard to reach loca-
after-sales service centre that is authorised to repair Bosch
tions
power tools.
Thoroughly clean the individual parts of the fine-spray
u
system immediately after each use, especially all
paint-carrying components. Proper cleaning is a pre-
requisite for faultless and safe operation of the spray gun.
No warranty claims will be accepted if cleaning has not
been done at all or has not been done properly.
Cleaning the air filter (see figure J)
The air filter (29) must be cleaned occasionally. The air filter
must be replaced if it is heavily contaminated.
– Open the air filter cover (26).
– Remove the air filter (29).
– Light contamination:
Knock on the air filter (29).
or
Heavy contamination:
Clean the air filter (29) under running water and sub-
sequently leave it to dry thoroughly, in order to prevent
mould from forming.
or
Replace the air filter (29).
– Reinsert the air filter.
– Close the air filter cover (26) again.
Never use the fine-spray system without air filter. Dirt
u
particles may get into the motor compartment and dam-
age it.
Cleaning After Using Water-Based Paints (see figure K)
Always clean the spray gun and the spray material container
with warm water.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch off the base unit (22) and remove the air
hose (20) from the spray gun (1).
– Remove the container (7) from the spray gun (1).
Hold the container (7) underneath the suction tube (13)
and pull the trigger switch (6) on the spray gun so that the
spray material can flow back into the container.
– Empty the container (7).
The spray material can be stored in an airtight, sealed
paint container for other applications. Use the spare
container (8) with cover or the original spray material
container, for example, for this purpose.
– Clean the container (7).
Bosch Power Tools