Jobsite CT0964 Instruction Manual
  1. Manuals
  2. Brands
  3. Jobsite Manuals
  4. Power Tool
  5. CT0964
  6. Instruction manual

Jobsite CT0964 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
230V WALL CHASER CT0964
INSTRUCTION MANUAL
IMPORTANT:
These instructions accompanying the product are the original instructions. This
document is part of the product, keep it for the life of the product passing it on to
any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CT0964 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Jobsite CT0964

Summary of Contents for Jobsite CT0964

  • Page 1 230V WALL CHASER CT0964 INSTRUCTION MANUAL IMPORTANT: These instructions accompanying the product are the original instructions. This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before assembling, operating or maintaining this product.

  • Page 2: Harmonized Standards

    In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 230V WALL CHASER Model: CT0964 Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU Harmonized standards：...

  • Page 3: Specification

    1. SPECIFICATION Rated voltage:230-240V~ , 50Hz Rated input power :1500W No load speed: 8500/min Slot depth: 5-29mm Slot width: 8-30mm Blade size: 125 x 22.23 x 2.2mm Sound Pressure Level (LpA): 97.1dB(A) K =3dB(A) Sound Power Level (LpA): 108.1dB(A) =3dB(A) Vibration Level: =3.239 m/s K=1.5m/s...

  • Page 4: Personal Safety

    outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. 2.3 Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

  • Page 5: Tool-Specific Safety Warnings

    breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Page 6 - The arbour size of wheels and flanges must properly fit the spindle of the power tool. Wheels and flanges with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
  • Page 7 WARNING! - Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Kickback is a sudden reaction to a pinched or snagged rotating wheel. Pinching or snagging causes rapid stalling of the rotating wheel which in turn causes the uncontrolled power tool to be forced in the direction opposite of the wheel’s rotation at the point of the binding.

  • Page 8: Technical Description

    edge of the workpiece on both sides of the wheel. - Use extra caution when making a “pocket cut” into existing walls or other blind- areas. - The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

  • Page 9: Unpacking And Checking

    4. UNPACKING AND CHECKING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the CANNONTOOLS and do not attempt to use the product.

  • Page 10: Operation

    6. OPERATION 1) Dismounting the Clamping Assembly (see figure). Press the spindle lock button (3) to lock the output shaft. Note: Actuate the spindle lock button(3) only when the spindle is at a standstill. Otherwise, the machine may become damaged. Loosen the clamping nut (8) with the two-pin spanner and unscrew the clamping nut (8).

  • Page 11: Maintenance & Troubleshooting

    the direction of the working-direction arrow . ● The machine can be both pushed or pulled in the cutting direction. Vertical Slots can easily be cut by pulling the machine from top to bottom. ● After finishing the working procedure, swivel the cutting unit out of the slot with the machine still running,until the cutting unit engages in the upper most position.
  • Page 12 If the body of the sander needs cleaning, wipe it with a soft damp cloth. Never use caustic agents to clean plastic parts. 8. SYMBOLS The use of symbols in this manual is intended to draw your attention to possible risks.

  • Page 13: Exploded View

    10. EXPLODED VIEW...

  • Page 14: Part Lists

    11. PART LISTS Part Name Part Name Scale plate Upper guard Active cover Self locking pin Compression spring Flat washer 6×14×1.5 φ7.8×φ0.7×2 Knob for scale plate Washer 5 Active cover ScrewST4.2×25-F Brand label Allen screw M8 Knob for active cover Small wheel Allen screw M6×30 Bearing 6000-2RS...
  • Page 15 Part Name Part Name Washer 4 Right handle Sealing washer for dust Capacitor Dust tube Switch Dust cover Switch button Screw M4×16 Cable jacket Front cover Cable Compression spring Sealing washer 15×27×4 φ5.3×φ0.7×16 Bearing 6201-2RS Unlocking button Bearing press plate Left handle Screw M4×12 Pressing board for cable...

Table of Contents