Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Jobsite CT5559
Summary of Contents for Jobsite CT5559
- Page 1 380W ELECTRIC NIBBLER CT5559 Ref no. YT-200E 1818 ORIGINAL INSTRUCTION Read the operating manual thoroughly before work and keep it for future reference. Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. 380W ELECTRIC NIBBLER Product description: YT-200E 1818 Model: CT5559 (Ref no. Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU Harmonized standards... -
Page 3: Specification
1. SPECIFICATION Rated Voltage:230V~ Rated frequency: 50Hz Rated input power: 380W Rated no load speed: 1800/min Protect class:II Degree of protection: IP20 Noise emmission: Lp=86.7dB(A), Lw=97.7dB(A) Cutting Capacity: Sheet Steel: 0. 5mm ~ 1. 8mm Stainless Steel: 0.5- 1. 2mm 2. - Page 4 a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Page 5 replacement parts. This will ensure that the safety of the power tool is maintained. 6) Additional Information. a) Wear ear protectors. Exposure to noise can cause hearing loss. b) Always wear eye protection. c) If the supply cord is damaged, it must be replaced by an authorized service agent in order to avoid a hazard.
-
Page 6: Technical Description
accessory. i) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. j) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. -
Page 7: Unpacking And Checking
4. UNPACKING AND CHECKING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the seller and do not attempt to use the product. -
Page 8: Functional Description
5. INSTRUCTIONS WARNING: Please read these instruction before you use this tool! It's possible you can be injured if you don't read & understand all instructions below. Remove the plug from the power supply before any maintenance is carried out. Check the voltage on the name plate is the same as your power supply. - Page 9 Permissible cutting thickness The thickness of material to be cut depends upon the tensile strength of the material itself. The groove on the die holder acts as a thickness gauge for allowable cutting thickness. Do not attempt to cut any material which will not fit into this groove.
- Page 10 metals. Always hold the tool body parallel to the grooves with the cutting head at a right angle (90°) to the cutting surface as shown in the figure. Replacement Instructions (Refer picture 2&3) : Replacement of down mould: Loosen two inner hexangular screws(4) slowly with hex Wrench (4mm) and replace with repaired down mould or new down mould (6), then tighten two screw (4).
- Page 11 6. DISPOSAL At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: ●...
-
Page 12: Expanded View
7. EXPANDED VIEW... -
Page 15: Part Lists
8. PART LISTS Description Description Power Cord & Cord Guard Eccentric Gear Shaft Tapping Screw ST3.9x16 Bearing 608Z Rear Motor Housing Motor Housing Gear Box Clamp Tapping Screw ST3.9x42 Press Board Dust Cover Tapping Screw ST2.9x10 Needle Bearing HK0608 Spring Washer Carbon Brush Gear Shaft... - Page 16 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...
Need help?
Do you have a question about the CT5559 and is the answer not in the manual?
Questions and answers