Steril-Aire UVC Controller II Installation And Operation Manual

Advertisement

Installation and Operation Manual
Improper installation, adjustments, alterations, service,
maintenance, or use can cause fire, electrical shock,
personal injury or property damage. Consult your supplier
or Steril-Aire for information or assistance.
DANGER, WARNING, or CAUTION are universally used
for overall safety. DANGER identifies the most serious
hazards which will result in severe personal injury or
death. WARNING signifies hazards which could result in
personal injury or death. CAUTION is used to identify
unsafe practices resulting in minor personal injury or
product and property damage.
WARNING:
Before performing maintenance,
ensure unit is unplugged. Electrical shock can cause
death.
CAUTIONS:
• Never expose eyes or skin to UVC light. Wear
gloves, face shield/glasses (per ANSI Z87.1) and
cover all exposed skin.
UVC Controller II
I
C
MPORTANT
ONSIDERATIONS
100/120/208/240/277VAC
UL File Number E841436
5,334,347/ 5,817,276/ 5,866,076/ 6,245,293/ 6,267,924/ 6,280,686/
6,313,470/ 6,372,186/ 6,423,882/ 6,500,267 /6,589,476/6,627,000/
6,783,578/7,140,749/ 7,282,728/ 7,459,694 & others pending
NOTE: Read the entire manual
before starting the installation.
• Do not touch Emitter
Damage to Emitter may result.
fingerprints will permanently etch glass of
Emitter and weaken structure.
using a Steril-Aire cleaning kit (included).
Isopropyl alcohol and a lint-free wipe may be
substituted.
• UVC Emitters are fragile. Handle UVC Emitter
with care.
• Voltages outside of the range designed for the
unit will void the warranty and do permanent
damage to the entire unit.
• Emitters contain mercury. If an Emitter breaks,
clean and dispose of with the same care as a
fluorescent lamp.
• UVC
energy
can
components. Protect such components with UV
resistant material such as aluminum foil,
aluminum duct tape, metallic shields, etc.
• The qualified installer or agency must use
factory kits and accessories when installing this
product.
MODEL: 8102PVAB
40A 9.6KW MAX
UL Approved
Patents:
Made in the USA
TM
glass without gloves.
Oil from
Clean Emitter
damage
non-metallic

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UVC Controller II and is the answer not in the manual?

Questions and answers

Matt Fiebelkorn
July 23, 2025

How can we change the light off delay when the doors are open.

Summary of Contents for Steril-Aire UVC Controller II

  • Page 1 Damage to Emitter may result. Oil from personal injury or property damage. Consult your supplier fingerprints will permanently etch glass of or Steril-Aire for information or assistance. Emitter and weaken structure. Clean Emitter using a Steril-Aire cleaning kit (included). DANGER, WARNING, or CAUTION are universally used Isopropyl alcohol and a lint-free wipe may be for overall safety.
  • Page 2: Installation

    NSTALLATION Ensure mains at the power panel are turned off before connecting power to the controller. Apply any necessary protection to assure that mains are not accidently turned on during the installation. 1) Caution use marked areas on the inside of the watchdog operation.
  • Page 3 Connection/Component Locations F1 & F2 0.5A 600V PN:80004125-500 TB2 Neutral/Ground F3 1.25A 250V 80004127 Circuit Breakers Remote Control & BMS Connections Display Menus & Status Menu/Select Button QR Barcode Link to Watchdog Manual...
  • Page 4 ENUS Home Menu: Displays Company name, Model number & Software revision. STERIL-AIRE Displays for 5 seconds on power up then changes to default menu. UVC CONTROLLER R1.00 The last menu viewed is saved as the default after 1 hour. Status Menu: Indicates global system status.
  • Page 5: Maintenance

    AINTENANCE Emitters need to be replaced every 9000 hours. Use Genuine Steril-Aire Emitters to maintain design output. If a Steril-Aire UVC Radiometer Kit is used, the Emitters should be replaced when the output falls below 50% of initial output. PARE OR...

This manual is also suitable for:

8102pvab

Table of Contents