Clarke CFP-2000DS Operator's Manual
Polisher
Hide thumbs
Also See for CFP-2000DS:
- Operator's manual (36 pages) ,
- Operator's manual (41 pages) ,
- Operator's manual (40 pages)
Table of Contents
Advertisement
Available languages
Available languages
Operator's Manual / Manual del operador / Manuel de l'utilisateur
01281A, 01280A, 01310A, 01320A, 01350A, 01431A,
MODELS:
01360A, 01390A, 01400A, 01401A, 01430A
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the
machine or to other property could occur as well. You must have training in the operation of this
machine before using it. If your operator(s) cannot read this manual, have it explained fully before
attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the ma-
chine.
Form No. 70880A
3/08 revised 11/13
CFP-130, CFP-170, CFP-200
CFP-1700, CFP-1700DS
CFP-2000, CFP-2000DS
Polisher
English (2 - 11)
EN
Español (12 - 21)
ES
Français (22 - 30)
FR
Advertisement
Chapters
Table of Contents
Related Manuals for Clarke CFP-2000DS
Summary of Contents for Clarke CFP-2000DS
- Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
-
Page 2: Table Of Contents
Modifi cations and additions to the cleaning machine which affect capacity and safe operation shall not be performed by the customer or user without prior written approval from Nilfi sk-Advance Inc. Unapproved modifi cations will void the machine warranty and make the customer liable for any resulting accidents. Clarke ® - 2 - FORM NO. 70880A... -
Page 3: English En
Read all machine labels before attempting to operate. Make sure all of the labels and instructional information are attached or fastened to the machine. Get replacement labels and decals from your authorized distributor. Clarke ® Operator's Manual (EN) - CFP Polisher... -
Page 4: Introduction
NOTE: This machine is intended for commercial use. MACHINE INTRODUCTION This product is intended for commercial use; polishing, spray buffi ng, scrubbing, stripping and rotary carpet shampooing. Clarke ® - 4 - FORM NO. 70880A Operator's Manual (EN) - CFP Polisher... -
Page 5: Accessories
6. Brushes with metal or wood backs and with holes to let the solution fl ow through. 7. Solution tank. 8. Sanding discs. 9. Solution Buff Accessory. WARNING: Use only brushes and accessories supplied by the manufacturer. Clarke ® Operator's Manual (EN) - CFP Polisher FORM NO. 70880A - 5 -... -
Page 6: Machine Specifi Cations
Tubular Steel Main Frame Die Cast Aluminum Height w/handle 46” (117 cm) Weight w/cord 87 lbs. (39.5 kg) 95 lbs. (43.1 kg) 81 lbs. (37 kg) Clarke ® - 6 - FORM NO. 70880A Operator's Manual (EN) - CFP Polisher... -
Page 7: How To Prepare The Machine For Operation
When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected. Contact the Clarke Customer Service Department. KNOW YOUR MACHINE (Figure 1) -
Page 8: Grounding Instructions
50 feet. Do not join two extension cords. Figure 3 Adapte Metal Scre Grounded Outlet Grounding Pin Grounded Outlet Box Clarke ® - 8 - FORM NO. 70880A Operator's Manual (EN) - CFP Polisher... -
Page 9: How To Operate The Machine
Perform any required maintenance or repairs before storage. Store the machine in a clean, dry place with the Operator Handle (6) locked in the upright position. Clarke ® Operator's Manual (EN) - CFP Polisher FORM NO. 70880A - 9 -... -
Page 10: Troubleshooting
• Call for service. LIGHT ON 1700DS / 2000DS MOTOR ILLUMINATES • Stop operating machine within 6 hours • Call for service • Replace carbon motor brushes. Clarke ® - 10 - FORM NO. 70880A Operator's Manual (EN) - CFP Polisher... - Page 11 ENGLISH NOTES Clarke ® Operator's Manual (EN) - CFP Polisher FORM NO. 70880A - 11 -...
- Page 12 Todas las indicaciones de dirección dadas en este libro están dadas desde la posición del operador en la parte de atrás de la máquina. Puede Ud. conseguir libros suplementarios dirigiéndose a su distribuidor Clarke. INDICE Instrucciones de seguridad para el operador ................13 Presentación de la máquina ....................14...
-
Page 13: Instrucciones De Seguridad Para El Operador
Procure que los componentes eléctricos sean siempre secos. Seque cuidadosamente la máquina después de cada utilización. Guarde la máquina en un local seco. Clarke ® Manual del operador (ES) - CFP Polisher FORM NO. 70880A - 13 -... -
Page 14: Presentación De La Máquina
Compruebe que todos los adhesivos y las instrucciones estén colocados en los sitios previstos. Si es preciso, haga un nuevo pedido a su distribuidor Clarke. ¡ AVISO ! No use la máquina como escabel o mueble. Corre el peligro de causar lesiones o daños materiales. -
Page 15: Accesorios
8. Discos para pulir. 9. Juego de accesorios para lustrar por pulverización con tampón. AVISO: Utilice únicamente las escobillas y los accesorios suministrados por el fabri- cante. Clarke ® Manual del operador (ES) - CFP Polisher FORM NO. 70880A - 15 -... -
Page 16: Especifi Caciones De La Puilidora
Alumminio fundido a presión Peso con manija 46” (117 cm) Peso (con cable) 87 lbs. (39.5 kg) 95 lbs. (43.1 kg) 81 lbs. (36.8 kg) Clarke ® - 16 - FORM NO. 70880A Manual del operador (ES) - CFP Polisher... -
Page 17: Preparación De La Máquina Para Trabajar
Si hay algún daño evidente, guarde la caja de embarque de modo que se la pueda inspeccio- nar. Comuníques con el Departamento de Atención al Cliente de Clarke. FAMILIARÍCESE CON SU MÁQUINA (Figura 1) Manijas para el operador Botón de cierre de seguridad de la palanca de... -
Page 18: Instrucciones Para La Conexión Con La Red 120 V
¡ AVISO !Use un añadido de cable de 12 AWG de sección. No use ningún añadido de más de 50 pies de largo. Nunca conecte dos añadidos. Figura 3 Adaptad Tornillo de M Receptáculo con Toma a Tierra Caja del Receptáculo con Toma a Tierra Conexion a Tierra Clarke ® - 18 - FORM NO. 70880A Manual del operador (ES) - CFP Polisher... -
Page 19: Funcionamiento De La Máquina
Guarde la máquina en un lugar limpio y seco, con la manija para el operador (6) trabada en posición vertical. Clarke ® Manual del operador (ES) - CFP Polisher FORM NO. 70880A - 19 -... -
Page 20: Detcción De Problemas
SE ILUMINA LUZ EN EL MOTOR 2000DS • Detenga el funcionamiento de la máquina en 6 horas. • Llame al servico técnico. • Reemplace las escobillas de carbón del motor. Clarke ® - 20 - FORM NO. 70880A Manual del operador (ES) - CFP Polisher... - Page 21 ESPAÑOL Clarke ® Manual del operador (ES) - CFP Polisher FORM NO. 70880A - 21 -...
- Page 22 Toutes les indications de direction fi gurant dans ce manuel sont visualisées depuis la position du conducteur, à l’arrière de la machine. Pour toute commande de manuels, adressez-vous à votre revendeur Clarke. INDEX Consignes de sécurité pour l’opérateur ......................23 Présentation de la machine ..........................
-
Page 23: Consignes De Sécurité Pour L'opérateur
Risque de court-circuit si les composants électriques d’une machine ont été exposés à l’humidité ou sont mouillés. Veillez à ce que les composants électriques soient toujours secs. Essuyer soigneuse- ment la machine après chaque utilisation. Entreposer la machine dans un local sec. Clarke ® Manuel de l’utilisateur (FR) - CFP Polisher... -
Page 24: Présentation De La Machine
fi gurant sur la machine avant la première utilisation. Vérifi ez que tous les auto- collants et les instructions sont positionnés aux endroits requis . Au besoin, recommandez-en chez votre revendeur Clarke. AVERTISSEMENT Ne pas utiliser cette machine comme escabeau ou comme meuble. Risque de blessure ou de dégât matériel. -
Page 25: Accessoires
Réservoir de solution Disques de ponçage Kit d’accessoires pour le lustrage par pulvérisation au tampon. AVERTISSEMENT: N’utiliser que les brosses et accessoires fournis par le fabricant. Clarke ® Manuel de l’utilisateur (FR) - CFP Polisher FORM NO. 70880A - 25 -... -
Page 26: Spécifi Cations De La Cireuse De Série C2K
Acier tubulaire Base Aluminium moulé Hauteur avec poignée 46” (117 cm) Poids (avec câble) 87 lbs. (39.5 kg) 95 lbs. (43.1 kg) 81 lbs.(36.8 kg) Clarke ® - 26 - FORM NO. 70880A Manuel de l’utilisateur (FR) - CFP Polisher... -
Page 27: Préparation De La Machine Avant La Mise En Service
Si elles sont endommagées, conservez la boîte d’emballage afi n qu’elle puisse être inspectée. Contactez im- médiatement le service d’entretien Clarke. CONNAÎTRE VOTRE MACHINE (Figure 1) Prises de la poignée de l’opérateur Bouton de verrouillage de sécurité... -
Page 28: Instructions Pour Le Raccordement Au Réseau 120V
à 50 pieds. Ne raccordez jamais deux rallonges. FIGURE 3 Adaptate Vis Metalliq Prise de Terre Socle de Prise de Terre Borne de Terre Clarke ® - 28 - FORM NO. 70880A Manuel de l’utilisateur (FR) - CFP Polisher... -
Page 29: Fonctionnement De La Machine
Conservez la machine dans un lieu propre et sec, avec la poignée de l’opérateur (6) verrouillée en position verticale. Clarke ® Manuel de l’utilisateur (FR) - CFP Polisher FORM NO. 70880A - 29 -... -
Page 30: Diagnostic
LE TÉMOIN LUMINEUX DU MOTEUR 2000DS S’ALLUME • Cessez d’utiliser la machine dans les 6 heures. • Contactez le service de réparation. • Remplacez les balais en carbone du moteur. Clarke ® - 30 - FORM NO. 70880A Manuel de l’utilisateur (FR) - CFP Polisher... -
Page 31: Section Ii Parts Manual
CFP Series 120V & 230V Section II Parts Manual (70880A) Operator's Manual- CFP Polisher FORM NO. 70880A - 31 - ® Clarke... -
Page 32: Assembly
9/11 ASSEMBLY - 32 - FORM NO. 70880A Operator's Manual- CFP Polisher ® Clarke... -
Page 33: Machine Schematic
71429A Label (CFP-2000 230/50) [ ] = Not Shown 71028A Label (CFP-2000DS 120/60) = Revised or new since last update 80290A Screw, 10-32 x 3/8 NOTE 1: The old handle assy consisting of the following parts (56057675, 441301) is no longer available. If you need to replace any of these components please order 56109699. -
Page 34: Motor Assembly And Schematics [Cfp-130,170, 1700, 200, 2000]
41053A Cord 12 IEC 60320 C20 Plug 747553 Strain ReliefSR7W2 CM20 747553 Strain ReliefSR7W2 CM20 53646A Gearbox 1.5HP 53645A Gearbox 1HP = Revised or new since last update - 34 - FORM NO. 70880A Operator's Manual- CFP Polisher ® Clarke... -
Page 35: Motor Assembly [Cfp-1700Ds, 2000Ds]
Varistor (Included with 8) 56039285 Speed Control 53849A Plate, Mounting 80141A Screw, 10-32 x 1 40851A Toggle Switch = Revised or new since last update 120V Motor Schematic Operator's Manual- CFP Polisher FORM NO. 70880A - 35 - ® Clarke... -
Page 36: Gearbox Assembly
GEARBOX ASSEMBLY Ref. No. Description 53645A Gearbox 1HP (CFP-130, CFP-170, CFP-200) 53646A Gearbox 1.5HP (CFP-1700, CFP-2000) 53647A Gearbox 1.5HP TS (CFP-1700DS, CFP-2000DS) 80141A Screw 10-32 X 1 Machine 980650 Wash .19 x .34 x .04 Lock 56922A Plateretainergearbox For 45 902606... -
Page 37: Accessories
Brick Grinding Medium Grit 451305 Brick Grinding Coarse Grit CFP-1700, CFP-2000 UNIQUE ACCESSORIES 11022A Kit Weight 52473A Capture Pwd 4-8 LBS Pails CFP-200, CFP-2000, CFP-2000DS COMMON ACCESSORIES 51707A Brush Polypro Scrub 20 56505920 Pad Holder-20 NP92 Clutch 480916 Brush Asm Polish FM/C/VP/DS- 975305... - Page 40 14600 21st Avenue North Plymouth, MN 55447-3408 www.clarkeus.com Phone: 800-253-0367 Fax: 800-825-2753 ©2013 Nilfi sk-Advance, Inc. A Nilfi sk-Advance Brand...