Related Manuals for DEL RollEasy2
Summary of Contents for DEL RollEasy2
- Page 1 A U T O M AT I C A B O V E - G R O U N D C O V E R RollEasy2 TECHNICAL INSTRUCTIONS Installation / Use / Cleaning / Maintenance / Safety advice...
- Page 2 NOTICE TO BE GIVEN TO THE USER AFTER INSTALLATION IS COMPLETE PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE. Electric and solar versions The motor is located in the stand and can be accessed from inside the housing. The power supply comes from an electric box located in the technical room, or from 2 batteries placed in the terminal on the motor side for the solar version.
- Page 3 - The motor (compliant with electric standards) is located in the tube and can be accessed from the exterior of the terminal. - Adjustment of the “mechanical automatic stop” locking the cover in place once it has been fully unrolled or rolled, is done directly on the motor.
-
Page 4: Delivered Parts
DELIVERED PARTS Free Electric Motorised roller Manual roller Solar Manual terminal terminal stand stand terminal terminal Electric or solar version assembly pack Ø12 Lag screw THEF screw TBHC screw Male Allen key Wrench Plug M8x80 M8x30 M6x30 size 4 M6 Nut M8 nut Ø24x2 Ø12x1.2... -
Page 5: Packing List
TOOLS REQUIRED FOR ASSEMBLY (INSTALLATION – 2 PERSONS) № 10 № 13 Ø8 - 12 № 17 ASSEMBLY INSTRUCTIONS 3 hours PACKING LIST e.g. - for a 4 x 8 m pool 1 0.80 x 0.60 x 0.55 pallet —- 40kg 1 4.30 x 0.20 m pack —–... - Page 6 ASSEMBLING AND FIXING THE ROLLER assembling the terminals Remove the terminal door. only for the electric and solar versions on the motor side M6 nut TBHC screw M6x30 M8 nut THEF screw M8x30 Assembling and placing the roller on the pool Manual version Solar and electric version Stand...
- Page 7 Fixture of the roller to the ground Ø24x2 Lag screw Ø12 washer Plug M8x80 Ø12 Solar and electric version 5 мм Installing the motor (electric and solar version) M6 nut Ø12x1.2 Ø12x1.2 washer washer align the key with the notch Make small rotating movement with the motor to facilitate the insertion...
- Page 8 ELECTRIC VERSION WIRING The electric box must be fitted in a dry place. The installation must be compliant with standard C15- 100. (Last applicable version) ask your electrician for advice or ask your electricity provider) All our boxes have a single phase 230 Volt (50Hz) power supply.
- Page 9 ELECTRIC VERSION WIRING...
- Page 10 WIRING - SOLAR VERSION - WI-KEY The electric box must be fitted in a dry place. The installation must be compliant with standard C15- 100. (Last applicable version) ask your electrician for advice or ask your electricity provider) All our boxes have a single phase 230 Volt (50Hz) power supply.
- Page 11 WIRING - ELECTRIC VERSION - WI-KEY...
- Page 12 WI-KEY INSTALLING THE CONTROL BOX red / green flashing = emitter locked Emitter unlocking procedure see «page 27» The emitter must be located outside volume 0. The distance between the emitter and the receiver must not exceed: - 50 m in an obstacle-free zone. - 25 m behind a basic wall.
-
Page 13: Cover Installation
COVER INSTALLATION Make sure the slats are in the right direction Roller water 35 cm If necessary, cut the sides to ease skid the passage of the strap cover and avoid rubbing Slat assembly By clipping “CLICK” along the whole length of the slat Repeat the movement until all the slats are completely clipped together By sliding... -
Page 14: Skid Assembly
Assembly of the strap between the cover and the tube The surface to be glued must be clean and notch Х Х skid assembly The skids are used to orient the cover at the start of closure. The holes are drilled at the factory. - Page 15 AUTOMATIC STOP ADJUSTMENT Command logic verification Opening the If the command logic is incorrect, cover reverse cables 1 and 2 on the motor output. (see wiring diagram) Closing the cover Adjustment The arrows indicate the cover’s direction of movement Turning in the + direction increases the extension of the cover Turning in the - direction decreases the extension of the cover...
- Page 16 OF THE LOCKING KITS The positions of the locking kits on the pool are shown on the plans delivered with the slats. Any changes to the positions of the locking kits must follow the rules explained below. Please contact us for any other cases. Positioning rules х...
- Page 17 PUSH-LOCK INSTALLATION A water level regulator is mandatory Insert mounted model Inserted For concrete and panel pools part Hollow white Ø16 washer 5 cm mini VBA TF Torx stainless steel A4 Ø6 x 50 wood screw Acceptable limit of level variation 50 mm water level recommended...
- Page 18 INSTALLATION QUICK-LOCK A water level regulator is mandatory Insert mounted model Inserted For concrete and panel pools part Hollow white Ø16 washer VBA TF Torx 5 cm stainless steel A4 Ø6 mini x 50 wood screw adjustement Acceptable limit of level variation 5 cm water level...
- Page 19 INSTALLATION PASSE-SANGLE A water level regulator is mandatory Insert mounted model Inserted For concrete and panel pools part Hollow white 5 cm Ø16 washer mini VBA TF Torx stainless steel A4 Ø6 x 50 wood screw Acceptable limit of level variation 5 cm water level recommended...
- Page 20 INSTALLATION OF THE STRAP-HOLDER ANCHOR EYEBOLT Eyebolt for concrete beach The head of the eyebolt must be higher than the beach surface between Ø20 25 et 40 cm depth : 5 cm Do not force the eyebolt into a drill hole of a smaller diameter than this Eyebolt for wooden beach Centre of the straplock...
- Page 22 ALWAYS KEEP AN EYE ON THE POOL DURING OPENING OR CLOSING OPERATIONS. ALWAYS CHECK THAT THE POOL WATER LEVEL IS CONSTANT AND COMPLIANT WITH THE RECOMMENDATIONS ON THE INSTRUCTIONS - It is imperative not to halt the cover in an intermediate position, this can cause the risk of jamming a bather’s body under the cover casing, if a bather uses the pool.
- Page 23 IMPORTANT When closing the pool, it is essential to KEEP THE CONTROL PRESSED FOR AT LEAST 3 SECONDS. This is required to guarantee automatic obstacle detection the next time the cover is opened. Locking Closure LOCKING THE WI-KEY • Press on for more than 3 seconds until the pilot flashes = system locked...
- Page 24 locking releasing...
- Page 25 Locking check that the system with the tool has kicked in Releasing with the tool the cover must not come out of the Quick-lock until the key switch has been turned (risk of re-triggering) Locking Pass the strap The strap must between the side and be tight the straplock rod...
- Page 26 - To ensure optimum safety and the correct operation of the roller, always check that the level of the water in the pool remains constant and compliant with the manufacturer’s recommendations. (For further comfort, use an overflow and a level regulator). - When the level is too high it is caused by the overflow being blocked by leaves or other debris.
-
Page 27: Replacing The Batteries
In the event of a motor or electric failure, you can remove the motor to close the pool manually. 1 - Cut the electricity supply 2 - Disconnect the motor 3 - Remove the fixtures and remove the motor 4 - Unroll the cover manually. 5 - Place the fastener kits. - Page 28 dear customers, You have chosen one of our automatic safety covers and we would like to thank you for your custom. Please read the recommendations below carefully. S A F E T Y N O T I C E · A pool can be a serious danger to your children. A drowning can happen quickly. Having children around a pool requires your constant vigilance and active watchfulness, even if they can swim.
Need help?
Do you have a question about the RollEasy2 and is the answer not in the manual?
Questions and answers