Advertisement
Quick Links
Speed Racer
ALPINE CHALLENGE
ITEM NO. 11157
BEFORE YOU BEGIN ...
1. Unpack the parts. Save the packing materials.
2. Match the parts to the drawings below.
3. If you have each part, put a check in the box next to the picture of the part. Look in the carton again and check all of
the packing materials to make sure you haven't missed anything.
The store where you purchased this item does not have parts. You will get the easiest service from Darda Division
of Life-Like Products, LLC Tell us the part(s) needed and be sure to include your name and address printed clearly.
Mail to DARDA / 1600 Union Avenue / Baltimore, MD 21211 / ATTN: Dock 2
CHECK LIST
SMALL JOINER (4)
LOOP JOINERS (16)
STACKING BRIDGE (10)
COUPLER (6)
TUNNEL (1)
SHEET OF STICKERS (1)
Connecting Track Using Track Joiners
Slide the Track Joiner - with the raised edges facing
down - half way into the channel on the underside of
the track piece. Now slide the adjoining track piece
over the open half of the joiner, so that it meets the
first piece. Be sure the tracks meet with no gaps.
LOOP HALVES (16)
14" STRAIGHT TRACK (6)
TRACK JOINERS (10)
LARGE JOINER (10)
FLEXI-CURVE (8)
DARDA CARS (2)
PAGE 1
!
CHOKING HAZARD
Not for Children Under 3 Years
IF A PART IS MISSING OR DAMAGED ...
7" STRAIGHT TRACK (2)
LARGE BASE PLATE (2)
BARS (18)
START/WIN BOX (1)
MOUNTAIN CUT-OUT(2)
ICICLES (2)
Track
Joiner
WARNI N G:
-
Small parts.
Raised edges
face down
Advertisement
Summary of Contents for darda Speed Racer ALPINE CHALLENGE
- Page 1 The store where you purchased this item does not have parts. You will get the easiest service from Darda Division of Life-Like Products, LLC Tell us the part(s) needed and be sure to include your name and address printed clearly.
- Page 2 Making Loops Pins • Put two loop halves together so that the pins at the Loop Joiners top of each loop half go into the proper holes, creating a tight fitting seam between the two loop halves. • Holding the loop halves together, slide one loop joiner over one end of the seam and the other loop joiner over *IMPORTANT: Make all 8 the other end of the seam.
- Page 3 STEP 1 FIGURE 1 • Start building the set by locating and First attaching one stacking bridge to one Loop baseplate. • Next, attach one end of a loop to the built-in track joiner on the stacking Second bridge , as shown to the right. Attach the other Loop end of the loop to the built-in track joiner in front of the stacking bridge on the baseplate.
- Page 4 FIGURE 3 STEP 3 Loop Flexi-Curve • Attach 2 loops to the built-in track Loop joiners on the 4 stacking bridges, as shown to the right. • Next, attach 2 flexi-curves using the built-in track joiners on the stacking bridges, as shown in Figure 3. Flexi-Curve FIGURE 4 STEP 4...
- Page 5 STEP 6 • Assemble the second half of the set, which is a mirror image of the half you just assembled. Figures 6.1 through 6.4 illustrate how to build the mirror image. Figure 6.5 shows the completed mirror image. FIGURE 6.5 FIGURE 6.1 Flexi-Curve Loop...
- Page 6 STEP 8 Get set, go! Press down the red button on the start-win box. A "brake" will emerge narrowing track so cars cannot pass. Rotate the checkered flag so it faces parallel to track. (White spokes will cross track on Checkered both sides when flag is in proper position.) Flag...