Related Manuals for SATO CG4 Series
Summary of Contents for SATO CG4 Series
- Page 1 Operator Manual For printer model: CG4 Series CG408DT CG408TT CG412DT CG412TT Direct Thermal Type Thermal Transfer Type Read this Operator Manual before and during usage of the above product. Keep this document handy for future reference.
- Page 2 SATO Corporation reserves the right to make changes and/or improvements in this product and document without notice at any time. Trademarks SATO is a registered trademark of SATO Corporation and/or its subsidiaries in Japan, the U.S and other countries. Version: SI-CG4-01rA-02-11-09OM ©...
- Page 3 If the fluid is drunk, voltage tion could cause a fire or electric immediately consult with a physi- • Do not use other than the specified shock. cian. voltage. Doing so could result in fire or electric shock. CG4 Series Operator Manual Page i...
- Page 4 • Do not operate the power result in injury. Be careful not to switch or plug in/unplug the become injured when replacing power cord with wet hands. paper or cleaning. Doing so could result in electric shock. Page ii CG4 Series Operator Manual...
- Page 5 Precautions for Installation and Handling Printer operation can be affected by the printer environment. Refer to the following instructions for installation and handling of CG4 Series printer. Select a Safe Location Place the printer on a surface that is flat and level.
- Page 6 7.2 RS232C Serial Interface ....................7 - 2 7.3 IEEE 1284 Parallel Interface..................7 - 6 7.4 Universal Serial Bus (USB) Interface ................7 - 9 7.5 Local Area Network (LAN) Ethernet................7 - 11 Page iv CG4 Series Operator Manual...
- Page 7 8.6 Offset position Adjustment ................... 8 - 9 8.7 Paper End ........................8 - 10 8.8 Ribbon End ........................ 8 - 11 Sato Group of Companies ..................9 - 1 Sato Group of Companies ....................9 - 2 CG4 Series Operator Manual Page v...
- Page 8 Table of Contents This page is intentionally left blank Page vi CG4 Series Operator Manual...
- Page 9 1.1 FEATURES OF THE PRINTER The CG4 Series is 4 inch Compact Desktop printer (Thermal Transfer or Direct Thermal). With a 32-bit RISC CPU, 4 ips print speed, and 4MB Flash Memory, the CG4 Series is an economical printer with numerous features making it suitable for a wide range of applications.
- Page 10 4. Set the printer on a solid, flat surface. Inspect the shipping container and printer for any sign of damage that may have occurred during shipping. Please note that SATO shall hold no liability of any damage of any kind sustained during shipping of the product.
- Page 11 ERROR indicator to show the modes of the printer. Press this button to turn the power on or off. FEED/LINE button Press this button to select the printer status (online/ offline) or to feed the media. CG4 Series Operator Manual Page 1-3...
- Page 12 To connect printer to the host computer using the USB interface. RS-232C interface terminal To connect printer to the host computer using RS-232C interface. Or, to connect the optional Keypad, Scanner or Smart keyboard to the printer. Page 1-4 CG4 Series Operator Manual...
- Page 13 This roller feeds the media. Perform top cover for ribbon loading. maintenance at regular intervals. Roll media holder Optional device compartment To hold the roll media. Used to install optional cutter or dispenser unit. CG4 Series Operator Manual Page 1-5...
- Page 14 Section 1: Introduction This page is intentionally left blank Page 1-6 CG4 Series Operator Manual...
- Page 15 The following information is provided: • 2.1 Site Location • 2.2 Media Selection • 2.3 Loading Labels • 2.4 Loading the Carbon Ribbon (For CG408TT, CG412TT only) • 2.5 Connections CG4 Series Operator Manual Page 2-1...
- Page 16 For optimal print performance and durability, please use SATO-certified label and ribbon supplies on this printer. Using supplies not tested and approved for use by SATO can result in unnecessary wear and damage to vital parts of the printer, and may void the warranty.
- Page 17 Media guides Note: Make sure the printed side of the media is facing upwards. Printed side should face upwards CG4 Series Operator Manual Page 2-3...
- Page 18 When replacing media, bear in mind that the print head and its surrounding area remain hot. Keep your fingers away from these areas to prevent injury. • Avoid touching even the edge of the print head with your bare hands. Page 2-4 CG4 Series Operator Manual...
- Page 19 • If the optional cutter or dispenser has been purchased, see Section 8.1 Optional Accessories - Cutter and Section 8.2 Optional Accessories - Dispenser on how to route the media. CG4 Series Operator Manual Page 2-5...
- Page 20 Avoid touching even the edge of the print head with your bare hands. 2.3.3 Overview of the Roll media and Fan-folded media loading path Roll media (Face-out) Fan-fold media Roll media (Face-in) (Printed side face up) Page 2-6 CG4 Series Operator Manual...
Need help?
Do you have a question about the CG4 Series and is the answer not in the manual?
Questions and answers