Table of Contents
Advertisement
Quick Links
Echoflex Installation Guide
ElahoAccess Interface
Overview
The ElahoAccess Interface is a wall
mounted device that works in
conjunction with the ElahoAccess
App. The Interface uses Bluetooth
Smart (aka Bluetooth Low Energy or
BLE) wireless technology to provide
access to the Elaho control system.
Use the Interface and the app
together to wirelessly configure
and control your Elaho Presets,
Spaces, Zones, and devices.
Specification
Installation Environment
For indoor, commercial controls use only. Echoflex recommends paying
special attention to the installation environment:
Indoor installation only 0°C–40°C (32°F–104°F), 5%–95%
•
non-condensing humidity.
A wireless operating distance of no more than 9.1 m (30 ft) between
•
the ElahoAccess Interface and the mobile device running the
ElahoAccess App.
Obstacles reduce the wireless transmission distance. When possible,
•
avoid transmitting through walls, ceilings, etc.
Electrical
24 VDC is required to power the interface. Run two each 1.5 mm
(16 AWG) wires (typically a black and red wire pair) from the auxiliary
power source for connection to the provided Aux Power pigtail.
Note:
electrical equipment. NEC Class 2 product to be wired in
accordance to NEC Article 725 and local jurisdiction requirements.
Corporate Headquarters n Middleton, WI, USA | +1 608 831 4116
Web
echoflexsolutions.com
©2022 Echoflex Solutions, Inc. Trademark and patent
Product information and specifications subject to change.
Echoflex intends this document to be provided in its entirety.
8186M2143 Rev C Released 2022-04
Installation must follow all national and local codes for
| Email
info@echoflexsolutions.com
®
| Support
service@echoflexsolutions.com
info: echoflexsolutions.com/ip
2
Advertisement
Table of Contents
Related Manuals for echoflex ElahoAccess
Summary of Contents for echoflex ElahoAccess
- Page 1 • non-condensing humidity. A wireless operating distance of no more than 9.1 m (30 ft) between • the ElahoAccess Interface and the mobile device running the ElahoAccess App. Obstacles reduce the wireless transmission distance. When possible, • avoid transmitting through walls, ceilings, etc.
- Page 2 The Interface connects to the EchoConnect station communication bus. EchoConnect is a bi-directional protocol that uses one pair of wires (data + and data -) for both data and power. Echoflex recommends using Belden 8471 Class 2 wire (or approved equal – see the Echoflex cable cross database echoflexsolutions.com/files/Elaho_Data_Cable_Wire_ Specs for equal alternatives).
- Page 3 Echoflex Installation Guide Access Interface Connect Wiring 1. Pull all required wiring into the back box. As needed, pull an additional ESD ground wire (required only when the Interface is not installed in grounded metal conduit). 2. Terminate the ESD ground wire pigtail.
- Page 4 Echoflex Installation Guide Access Interface Note: When using Category 5 (or equivalent) cable on the EchoConnect communication bus, please note the following: Cat5 wiring must be terminated using EchoConnect Cat5 • Termination Kits and must be installed using a bus topology.
- Page 5 Bluetooth - The bottom yellow LED lights and blinks when an active Bluetooth radio is paired with a mobile device. Note: For more information on configuring devices via Bluetooth connection, see the ElahoAccess App integrated help system. Additional information on Elaho systems is available at echoflexsolutions.com. Install the wall plate The wall plate is secured to the Interface with built-in magnets.
- Page 6 Restore Factory Defaults The Reset button on the back of the ElahoAccess Interface lets you restore the Interface to its default factory settings. Reset Button 1.
- Page 7 • that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help • Compliance For use with Echoflex Elaho Control Systems, powered by Elaho power supplies. Bluetooth SIG compliant (see Bluetooth above FCC Compliance...
- Page 8 Echoflex Installation Guide Access Interface Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Need help?
Do you have a question about the ElahoAccess and is the answer not in the manual?
Questions and answers