Related Manuals for Jetting MJet V0 HD
Summary of Contents for Jetting MJet V0 HD
- Page 1 MJet V0 HD Product model/type: MJet V0 HD 18 V MJet V0 HD 18 V USER'S GUIDE AND SAFETY MANUAL...
- Page 2 For permission requests, write to the publisher, addressed “Attention: Permissions Coordinator” at the address below. Jetting AB, Murgatan 1, 522 35 Tidaholm, Sweden jetting.se info@jetting.se...
- Page 3 Important safety notice Read and understand all procedures and safety instructions before using the MJet V0 HD micro fibre blower. Observe all safety information on this page and note specific safety requirements as explained by procedures in this manual. Failure to follow these instructions could result in serious personal injury or death.
-
Page 4: Table Of Contents
Table of contents Section Page General information Technical information Safe operating practices Unpacking the box Set up the blower Display functions Crash test Blower operations Maintenance Troubleshooting guide EC Declaration of Conformity Notes... -
Page 5: General Information 1
1. General information The MJet V0 and V0 HD is unique devices for installing fiber optic directly into a pipe. The MJet V0 HD is consist of an air block/pipe clamp and a drive wheel that, when combined installs a fiber into an airtight pipe. -
Page 6: Technical Information
2. Technical information A. Condition of use Temperature from -15° C to +40° C Humidity from 20 % to 90 % Weather conditions relevant to working conditions Natural and/or artificial lighting of the work site, >200 lux B. Air compressor requirements Pneumatic pressure 16 bar maximum Required air flow... -
Page 7: Safe Operating Practices
Keep hands away from belt drive while blower is in operation. B. Working with air The MJet V0 HD, using pressurized air to project the fiber at high velocities. Please observe the following precautions when operating the blower: Forced air creates flying debris. Always wear personal protective equipment. -
Page 8: Unpacking The Box
• Never expose the charger to rain, moisture or damp. If you suspect any of thes have occurred then do not use the charger. • Only charge your battery using the compatible Jetting charger provided with your battery. Never discharge your battery other than in normal use on the MJet V0. -
Page 9: Set Up The Blower
MJet V0 HD. The MJet V0 HD must be positioned in-line between the fiber to be installed and the pipe. The fiber should not enter the MJet V0 HD at an angle of more than 10 degrees from the... -
Page 10: Display Functions
Fiber Crash Testing is a very quick and easy step to be completed before attempting the installation of fiber with the MJet V0 HD. This test is necessary to set the push force control of the motor below the point that the MJet V0 HD may cause fiber damage as a result of over pushing or encountering an obstruction in the sub-duct system. -
Page 11: Blower Operations
Insert the fiber and seal inside the pipe clamp as it would be for the actual installation. Install a 1 to 2 m test length of pipe into the MJet V0 HD clamp and insert clamp into the air block. -
Page 12: Maintenance
Wheel cleaning and tightening use, or when necessary Disconnect power supply and exhaust any air pressure before servicing any component on the MJET V0 HD. Avoid handling leaking couplings, valve seal or inadequately sealed pipe in air block. DANGER! Risk of air under pressure penetrating skin. -
Page 13: Troubleshooting Guide
10. Troubleshooting guide Fiber becomes jammed in the pipe 1. Inform the people at the other end of the pipe that a problem has been experienced and the operator is going to shut down the system. 2. Shut off the pneumatic air supply with the air control valve, allowing the air pressure to be depressurized from the pipe and the pipe clamp air block. -
Page 14: Ec Declaration Of Conformity 11
11. EC Declaration of Conformity... -
Page 15: Notes
12. Notes... - Page 16 MJet V0 HD 18 V USER'S GUIDE AND SAFETY MANUAL...