Clarion APX200.2 Operating & Installation Manual
  1. Manuals
  2. Brands
  3. Clarion Manuals
  4. Car Amplifier
  5. APX200.2
  6. Operating & installation manual

Clarion APX200.2 Operating & Installation Manual

Clarion power system operation installation manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Clarion APX200.2

Summary of Contents for Clarion APX200.2

  • Page 2: Table Of Contents

    • Low profile, compact size for space limited installations ABOUT THE MANUAL AND W ARRANTY To start enjoying your new Clarion two-channel amplifier, please read the instructions listed in this manual. Keep all instructions for future reference. Please fill out and send in the enclosed warranty card to protect your purchase and aid in warranty service.

  • Page 3: Description

    Protection circuits safeguard the amplifier when overheating and speaker shorts or improper load conditions occur. All connections and controls of the APX200.2 and APX400.2 are on the end panels and are easy to understand. We use gold-plated RCA and barrier connectors to ensure the best electrical connection for your system.
  • Page 4 • Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier’s range, 250mV to 2.5V for RCA inputs or 500mV to 5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit.

  • Page 5: Connections For Power And Speakers

    CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX200.2 and APX400.2 both contain power and speaker connections as shown below. Figure 2- 1. Left Speaker Output 2. Right Speaker Output 3. Remote Turn-on Input 4. Ground Input 5. Battery + 12v Input...

  • Page 6: Applications

    APPLICATIONS The Clarion APX200.2 and APX400.2 2-channel car audio amplifiers can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged- Mono Subwoofer System Set X-Over Mode to LP and adjust FREQ to speaker specifications.
  • Page 7 2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or satellite or subwoofer) speakers.
  • Page 8 Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) FREQ (hz) L (mH) NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave crossover at specified frequencies.

  • Page 9: Installation

    Instead, see your authorized Clarion dealer for installation recommendations. MOUNTING PRECAUTIONS Although the Clarion APX200.2 and APX400.2 both incorporate heat sinks and protection circuits, mounting the amplifier in a tight space without any air movement can still damage internal circuitry over time. Choose a site that provides adequate ventilation around the amplifier.
  • Page 10 4. A secure clean ground connection is critical to the performance of your Clarion amplifier. Use the shortest ground wire possible snd securely connect to the car chassis to minimize resistance and avoid noise problems. 5. Add an external fuse on the amplifier’s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal.
  • Page 11 Figure 6. - Electrical connections for the APX200.2 or the APX400.2...

  • Page 12: Setting The Gain

    4. Slowly increase the Gain Control. Stop when you hear a slight distortion of audio. SETTING THE CROSSOVER The Clarion APX200.2 and APX400.2 feature a fully adjustable crossover. To set the crossover, follow these steps. 1. Using the X-Over Mode Switch, select the desired mode - LP for Low Pass, HP for High Pass and OFF for Full Range.

  • Page 13: Final System Checks

    Speakers not connected or are blown. Check speaker connections at amplifier, measure coil impedance. Problem Audio cycles on and off. Solution Thermal protection circuits are shutting amplifier off. Check location for adequate ventilation; consult an authorized Clarion Audio Dealer.

  • Page 14: Product Specs

    Max. Power Output Cont. Power Output 2-Ohm Stereo Output Bridged Power Dimensions Current Consumption at output @ max power APX200.2 20Hz ~ 20kHz >100db .05% all channels driven 250mV ~ 2.5 V 500mV - 5V 220w (110 x 2) 100w (50w x 2) @.08% THD 110 x 2 @ .05% THD...

  • Page 15: Notes

    NOTES...
  • Page 16 661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX2CH-10 Rev.1 (02/00)

This manual is also suitable for:

Apx400.2

Table of Contents