Figures - ABB HT564131 Operation Manual

Operation Manual / 4 Product description / A130-M.. - A145-M..

Figures

Figures
Fig. 1 Layout and function of the tur-
bocharger ..................................
Fig. 2 Compressor wheel cooling ........
Fig. 3 Warning plate locations .............
Fig. 4 Locations of the rating plates ....
Fig. 5 Suspension of complete turbo-
charger unit ...............................
Fig. 6 Removing the turbocharger .......
Fig. 7 Loosening the clamping nut ......
Fig. 8 Turbocharger centre of gravity ..
Fig. 9 Inserting gaskets into the
bracket ......................................
Fig. 10 Inserting the threaded rods .......
Fig. 11 Requirements for threaded rods
Fig. 12 Placing the turbocharger on the
bracket .....................................
Fig. 13 Preparing the clamping nut for
the tightening procedure ..........
Fig. 14 Tightening pressure screws ......
Fig. 15 Connecting the compressor
cooling air intake .......................
Fig. 16 Attaching the support ................
Fig. 17 Oil orifice ...................................
Fig. 18 Layout and overview of speed
measurement system ................
Fig. 19 Replacing the speed sensor ......
Fig. 20 Noise insulation, bellows ...........
Fig. 21 Replacing the protective grid .....
Fig. 22 Carrying out wet cleaning of
compressor ...............................
Fig. 23 Carrying out wet cleaning of
turbines .....................................
Fig. 24 Cleaning the filter silencer .........
Fig. 25 Compressor-end, non-rotating
parts ..........................................
Fig. 26 Turbine end, non-rotating parts .
Fig. 27 Soaking the turbine end ............
Fig. 28 Weights of assemblies ..............
Fig. 29 Removing the air inlets ..............
Fig. 30 Removing the gas outlet casing
© Copyright 2016 ABB. All rights reserved.
Fig. 31 Dismantling the gas outlet
6 flange ........................................ 81
7 Fig. 32 Removing the gas outlet flange . 82
8 Fig. 33 Removing the compressor cas-
ing ............................................. 83
9
Fig. 34 Dismantling the wall insert ......... 84
11 Fig. 35 Removing insulation sheets ...... 85
12 Fig. 36 Oil orifice ................................... 85
14 Fig. 37 Removing cartridge group 1 ...... 86
15 Fig. 38 Removing cartridge group 2 ...... 86
Fig. 39 Removing the nozzle ring .......... 87
16
Fig. 40 Installing the cartridge group on
17 the service support .................... 88
17 Fig. 41 Measuring clearance A and B ... 89
Fig. 42 Nozzle ring compression PD ..... 90
18
Fig. 43 Installing the nozzle ring ............ 91
Fig. 44 Lifting the cartridge group and
20
rotating it by 90° ........................ 92
21
Fig. 45 Installing the cartridge group ..... 93
Fig. 46 Turbine casing insulation / Burst
22
protection .................................. 94
22
Fig. 47 Installing the compressor casing
24 .................................................. 96
Fig. 48 Measuring clearances N and R . 97
32
Fig. 49 Installing the air inlets ................ 98
34
Fig. 50 Installing the gas outlet flange ... 99
36
Fig. 51 Installing the gas outlet casing .. 99
39
Fig. 52 Tightening torques ................... 100
Fig. 53 Tightening torques for insulation 101
49
Fig. 54 Fitting the cover plate ................ 105
Fig. 55 Cover plate drawing .................. 106
53
Fig. 56 Overview of part numbers ......... 112
55
57
58
61
77
78
79
HZTL4031_EN
Page 115 / 117
Revision D June 2016