Advertisement
Quick Links
Record your model number: __________________________
1503912-T2
INSTALLATION INSTRUCTIONS
TP HOLDER (W/ TRAY)
K-29221T-**/K-29222T-**/ K-29223T-**/ K-29227T-**/ K-29228T-**/ K-29231T-**
DOUBLE TP HOLDER (W/ TRAY)
K-29224T-**/K-29225T-**/ K-29226T-**/ K-29229T-**/ K-29230T-**/ K-29232T-**
All information is based on the latest product information available at the
time of publication. Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important
information.
NOTE:
These products should be located and mounted to a wall. While it is possible
to mount them to any surface, a stud, concrete and drywall mounted product
will yield the best results.
DANGER: (Risk of personal injury )
These products are not designed or intended for use as a grab bar or support
bar. Do not install any of these products in any area where they are likely to
be used inadvertently as a grab bar or support bar.
Follow all local plumbing and building codes.
1. Drill bit
2A. TP HOLDER (WITH TRAY): Using the provided screw, secure the holder
to the tray with a screw driver.
3B. DOUBLE TP HOLDER (WITH TRAY): Using the provided screw, secure
the holder to the tray with a screw driver.
4. Position the tray on the wall and mark the hole points for drilling.
5. Drill diameter 3mm holes to install on stud, 8mm holes for drywall and
6mm holes for concrete wall.
6. No plugs are required, when mounted to a wood-panel wall.
6A. Installation of butterfly anchors to drywall.
Hold the butterfly anchor and fold the edges inside, insert the butterfly anchor
into the drilled hole, stretch it with pin and tap with hammer until it flush
with the wall.
7B. Installation wall anchor to Concrete wall: Install wall anchors into the hole
and tap with hammer until it flush with the wall.
8. Use the screws provided in the accessory kit to secure the tissue holder to
the wall through the retaining ring.
9. Secure the cover on the ring by screwing on top of the ring.
ROUGH-IN (Unit: mm).
10. K-29221T-**/K-29222T-**/K-29223T-**
1503912-T2-A
1
3
B
Holder
5
7
B
9
1
2
Holder
4
Tray
Screw
6
8
10
150
Tray
Screw
A
190
Kohler Co.
Advertisement
Related Manuals for Kohler K-29221T Series
Summary of Contents for Kohler K-29221T Series
- Page 1 K-29224T-**/K-29225T-**/ K-29226T-**/ K-29229T-**/ K-29230T-**/ K-29232T-** All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. Screw Holder Please leave these instructions for the consumer.
- Page 2 After wiping the product with cleaners, please immediately wipe and rinse the surface with water. At the same time, wipe cleaners splashed around. Please use soft and wet sponge or cloth. Do not use abrasive cleaning materials such as bushes or scouring pads. 1503912-T2-A ©2022 Kohler Co.
- Page 3 2A. 卫生纸架（带置物平台): 使用提供的螺丝, 将支架固定到托盘上. 3B. 双层卫生纸架（带置物平台): 使用提供的螺丝, 将支架固定到托盘上. 4. 标记钻孔位置. 5. 安装到木板墙上，钻直径为3mm的孔. 安装到石膏板墙上, 钻直径为8mm的 孔. 安装到混泥土墙上, 钻直径为6mm的孔. 6. 安装到木板墙, 则不需要涨塞. 6A. 将蝴蝶涨塞安装到石膏板墙上： 握住蝴蝶涨塞并将边缘向内折叠, 插入钻孔内, 用销钉将其顶开并用锤子轻敲直 到它与墙壁齐平. 7B. 将涨塞安装到混凝土墙上：将涨塞插入钻孔内并用锤子轻敲直到它与墙壁 齐平. 8. 使用附件包内提供的螺丝, 穿过固定环将纸巾架固定到墙上. 9. 将盖子拧到固定环上. 尺寸图 单位：毫米. 10. K-29221T-**/K-29222T-**/K-29223T-** 1503912-T2-A Kohler Co.
- Page 4 尺寸图 单位：毫米. 11. K-29224T-**/K-29225T-**/K-29226T-** 12. K-29227T-**/K-29228T-** 13. K-29229T-**/K-29230T-** 14. K-29231T-** 15. K-29232T-** 清洁和保养 在清洁产品时, 请使用温和的清洗剂，如液体清洗剂和 温水. 请勿使用研磨性的 清洁用品或高浓度擦洗剂, 否 则会损坏产品表面或使其失去光泽. 仔细阅读清洗剂的说明书, 以确保该类清洗剂适用于 本产品. 在清洗整个产品前, 请在产品的不显眼处试用该清洗剂. 在使用清洁剂擦洗产品后, 请立即用水擦净并冲洗表面. 同时请擦去溅洒到附近 表面的清洁剂. 请使用柔软湿润的海绵或布。请勿使用刷子或百洁布等 磨损性的清洁材料. 1503912-T2-A ©2022 Kohler Co.