JVC CH-X1500 Instructions Manual page 14
Jvc ch-x1500: instruction manual
Hide thumbs
Also See for CH-X1500:
- Service manual (65 pages) ,
- Instructions manual (13 pages) ,
- Schematic diagrams (8 pages)
Table of Contents
Advertisement
A
When installing the unit horizontally
1. Attach the mounting brackets on the side panels of the unit using
screws. (Fig. a)
2. Install the unit on the floor of the trunk using self-tapping screws.
(Fig. b)
1.
Screw
(M4 x 8 mm)
(M4 x 8 mm)
Mounting bracket
x M4
Fig. a
=a
a
B
When installing the unit upright
Fig. c
=c
c
Notes:
• When attaching the unit with the screws, refer to "
installing the unit horizontally" above.
• When installing the unit upright, set the selectors located
on both sides to the "V (vertical)" position. (When it is
installed horizontally, be sure to set the selectors to the "H
(horizontal)" position.)
– When installing the unit upright, securely install to the trunk
floor.
• If you install the unit without setting the selectors correctly, the
symptoms below may occur.
– Sound is intermittent.
– CDs are damaged.
C
When installing the unit on an inclined plane
(Fig. d)
Fig. d
=d
d
Notes:
• When attaching the unit with the screws, refer to "
installing the unit horizontally" above.
• When installing, five angles can be selected. Be sure to
position the selectors on both sides of the unit pointing
upward, perpendicular (90°) to the earth surface.
• If you install the unit without setting the selector correctly, the
symptoms below may occur.
– Sound is intermittent.
– CDs are damaged.
D
When hanging the unit in the trunk space
(Fig. e)
Fig. e
=e
e
Note:
When attaching the unit with the screws, refer to "
the unit horizontally" above.
!"#$%&
!"#$%&'()*+,-E =aF
1.
!"#$%&'()*+,-./012E =bF
2.
Use these holes.
!"#
!"#$%&
(Fig. c)
Selector
Bottom panel of the unit
!"#
!"#$%&'()*+,-./0=A=
A
When
•
!"
!"#$%&'()$*+,-.$/01V
•
!"#$%&'()*+,-./01234H
!"#$
!"#$%&'()*!+,-) ./01234
–
!"#$%&'()*+,-.&/01234567
•
!"#$%&'
–
!"#$%
–
!"#$%&'(=
Side panel of the unit
!"#
!"#$%&'()*+,-./0=A=
A
When
•
!"
!"#$%&'()*+,-./012345%&2
•
!"#$%&'()* 90
!"#$%&'()*+,-.&/01234567
•
!"#$%&'
–
!"#$%
–
!"#$%&'()*+,=
!"#$%&'()*+,-./0=A=
A
When installing
5
3
4
1
2
=E =cF
Use these holes.
Trunk floor
!"
!"#
E =dF
45
Trunk floor
!"#
E
eF
!"#$%
2
2.
Trunk floor
!"
Fig. b
=b
b
c
!"#
3
1
2
A
V
H
CD
d
Selector
!"
A
CD
e
2
1
4
3
Use these holes.
5
!"#
A
a
b
Tapping screw
(M5 x 20 mm)
(M5 x 20 mm)
x M5
Drill holes
5
4
•
•
–
•
–
–
•
•
•
–
–
Hide quick links:
Advertisement
Table of Contents
