In this connection, read the following operating instructions. Follow the instructions in the manual. When handing over the machine to third parties, hand over and all the documentation. - 3 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
In case of electric shock! Injury immediately disconnect the electrical supply through pulling the plug out of the socket! Get medical attention immediately - 4 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
22. Sticker ‘Label path for STS810‘ Scope of the delivery. Check immediately after unpacking the machine: - 1 machine STS815 with marking printer; - 1 ink cartridge for marking printer; - 1 power cable 220V, 3x0.75mm2, 1.8m; - 1 signal cable 4x0.25mm2, 1m, with M12-4P connectors;...
Page 7
Guiding Parts 1 Roll with labels Tape with marked labels INPUT1 INPUT2 Base film Guiding Parts 2 Label Finisher STS815 Tensioner The roll for pulling the base film Figure 1.2 - 6 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu...
- Do not remove the vessel from the machine before the shafts rotation is stopped. Failure to keep the above instructions may result in injuries or damages. - 7 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www.
The printer rollers should rest well on the rotating guide elements. Starting the labeling machine leads to automatic operation of the marker. - 8 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
Page 10
Guiding Parts 1 Roll with labels Tape with marked labels Base film Guiding Parts 2 Tensioner The roll for pulling the base film fig. 3.2 - 9 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
The machine stops automatically. This is indicated by 3 blinks followed by a pause - with a red light. To exit emergency mode, it is necessary to turn off the power. - 10 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
If the power cord is damaged, replace it with a new one. This ensures the protection against electric shock and guarantees the safety of the machine. - 11 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
According to European Union Directive 2002/96 / EU, end-of-life electrical appliances must be collected separately and disposed of for recycling in accordance with environmental protection requirements. - 12 - V.1.00 STS815 phone: (+359) 66 801 536 fax: (+359) 801 547 info@stselectronics.eu www. stselectronics.
EC DECLARATION OF CONFORMITY - original With the present STS Electronics Ltd., Gabrovo, 41 Industrial Street, tel .: 066/801536, e-mail: info@stselectronics.eu manufacturer Declares under its own responsibility that the machine STS 8 15 for marking labels complies with the requirements of:...
Need help?
Do you have a question about the STS815 and is the answer not in the manual?
Questions and answers