Advertisement
JA-169P outdoor dual PIR motion detector
The following table represents the values included in the figure:
Position
Maximum range of the lower detecting part
A
B
C
D
E
Table 1: Detection range
Warning: The maximum detection length of the lower detection plane
may vary from the values listed above due to varying environmental
thermal conditions. This must be taken into consideration during
detection range adjustment.
The detection area angle is 85°. Direction of the detection angle can
be adjusted to positions A – G by rotating the detector´s adjustment
knob. Each step is marked. The detector's lens covers the angle of 180°
- therefore the lens does not require any adjustment.
The PIR detection sensitivity can be configured by a 10-pole switch
located next to the upper sensor.
DIP2
DIP3
OFF
OFF
low
OFF
ON
low / medium
ON
OFF
medium / high
ON
ON
high
Table 2: PIR sensitivity
DIP4
DIP5
OFF
OFF
PIR1 - ON, PIR2 - ON
OFF
ON
PIR1 - ON, PIR2 - OFF
ON
OFF
PIR1 - OFF, PIR2 - ON
ON
ON
not available
Table 3: Working logic
The detector sends information to the control panel every 9 minutes.
For normal detector operation we recommend the LED indication to be
turned off in order to save battery life. The inhibition mode can be set by
DIP switch no. 9, selecting between 180 s and 30 s. It determines the
time period after which the detector is able to detect movement again
and send a new activation signal.
Testing (coverage test)
DIP switch Nº1 is set to TEST position in default. DIP switches Nº2
and Nº4 are recommended to be turned on for coverage test.
Once the detector has been enrolled into the system and powered up,
TEST mode will commence and every single activation is being indicated
by an LED and status is sent to F-Link diagnostics, after four minutes of
inactivity the detector automatically exits said testing mode and will
commence normal operation.
After testing set DIP switch Nº1 to NORM position. For saving battery
it's recommended to set off LED indication and set on the power saving
mode to 120 s.
Troubleshooting
False alarms:
−
Check if it's mounted in right height range and perpendicular to
the ground
−
Check if the detection area of lower PIR sensor is not wider than
required
−
Check if the detection area doesn't contain moving objects
Terminal description of JA-150TX-V1
IN
detector activation
TMP
tamper contact
COM
common ground
AUX
connected with GND
LoB
connected with GND
GND
ground
+U
power
Table 4: Connection description between JL01 and JA-150TX-V1
JA-169P
3 m
5 m
7 m
10 m
15 m
PIR sensitivity
Working Logic
brown
white
gray, pink
black
red
2/2
Technical specifications
Power:
1x Lithium battery type CR123A (3.0 V/1.4 Ah)
Current consumption (quiescent/maximal)
Typical lifetime of battery
Communication band
RF range
Maximal radiofrequency power (ERP)
Detection characteristics
Weight (w/o battery)
Recommended installation height
Speed of object movement
Saving power timer of battery
Operating temperature range
Detector cover conformance
Average operating humidity
Dimensions
Weight (w/o battery)
Can be operated according to
JABLOTRON
the JA-169P detector is in a compliance with the relevant
Union harmonisation legislation: Directives No: 2014/53/EU,
2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the
conformity assessment can be found at www.jablotron.com -
Technical Section Downloads.
Note: Disposing of this product correctly will help save
valuable resources and prevent any potential negative effects
on human health and the environment, which could otherwise
arise from inappropriate waste handling. Please return the
product to the dealer or contact your local authority for further
details of your nearest designated collection point.
Please note: Batteries are not included
30 µA/55 mA
approx. 3 years
- when 120 s saving mode is used
868.1 MHz
up to 300 m (open area)
15 m/85 °; 11 segments
1–1.2 m
0.3–1.5 m/s
30 s or 120 s
-25 °C to +60 °C
75%, non-condensing
189 x 81 x 98 mm
ERC REC 70-03
ALARMS
a.s.
hereby
declares
MMY57100
25 mW
380 g
IP45
380 g
that
Advertisement
