All manuals and user guides at all-guides.com Service PMD670 / W1B/U1B/F1B Manual Solid State Recorder STEREO -20dB AUTO MARK ANALOG OUT MIC ATTEN SOLID STATE RECORDER PMD670 SINGLE FLAT REPEAT PRE REC LIMITER MANUAL INPUT LOCK EDL PLAY LEVEL CONT. EDIT...
Page 2
Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
All manuals and user guides at all-guides.com 1. TECHNICAL SPECIFICATIONS Digital audio system Outputs System LINE OUT L/R Solid State recorder Type: RCA jack Usable Media Standard level: 2 Vrms max./2 kohms IC memory cards and HDD(Micro Drive) cards DIGITAL OUT Recording and reading method Type: RCA jack MPEG1 Layer 2/3 compression...
All manuals and user guides at all-guides.com 2. FACTORY/SERVICE MODE A. FACTORY MODE To reset all settings to default status ,follow the procedure below. 1. When Power Standby mode, While pressing A-B REPEAT and INPUT buttons, Slide POWER switch to turn on the unit.
All manuals and user guides at all-guides.com 3. LCD CONTRAST ADJUSTMENT 1. Connect the TEST POINT (See below) with the tester. 2. Turn the variable resistor RF01(RF09) so that the reading of the tester becomes 7.0 V ± 0.1 V and conferm the contrast of the LCD becames maximum.
Page 6
All manuals and user guides at all-guides.com 4) Remove 2 screws from both sides as shown in Fig.3 and Fig.4. <Fig.3 Po si tion of screw> <Fig.4 Position of screw> 5) Remove the front panel, holding it and pushing down with thumb as shown in Fig.5 and Fig.6.
Page 7
All manuals and user guides at all-guides.com 7) Remove 5 connectors as shown in Fig.8. And remove the top case. <Fig.8 Position of connectors> 8) Remove 4 connectors as shown in Fig.9. <Fig.9 Position of 4 connectors> 9) Remove 5 screws. Then remove side panel of Audio I/O side.
Page 8
All manuals and user guides at all-guides.com 10) Remove 6 screws. Then remove side panel of CompactFlash side. <Fig.11 Position of 6 screws> 11) Remove 7 screws. Then remove the PCB. <Fig.12 Turning over the Main PCB> <Fig.12 Position of 7 screws>...
• CompactFlash (with format) Update Disc (*PMD670CDR) • Connection 1. Connect Windows PC and PMD670 with USB cable 2. Insert the CompactFlash mini USB 5pin Writing procedure NOTICE : Don't turn off the power during the update. When turn off the power, you must change Flash Rom (QD01).
Page 10
When "pmd_prog.bin" isn't delete from the compacFlash, The set becomes the mode of update of fi rmware every time to turn on the unit. 15. Disconnect USB cable from the PMD670, then turn off POWER switch. 16. Check the version number of the fi rmware Refer to 2-page "SERVICE MODE"...
1. Connect COM port of Windows PC and Flash Writer with RS232C cable 2. Connect Flash Writer and JIG PCB with Parallel cable 3. Connect 5pin USB mini cable to I/O port of PMD670. Preparation (The installation procedure of the Update software) Open FLASH2 Disc , and double click "Setup.exe", and...
Page 12
All manuals and user guides at all-guides.com Start Installation . Click Next Click Next (when you must change the installation Folder, Select the Folder ) Click Next...
Page 13
The icon of Flash2 is made in the desk-top computer. Confi guration Connect AC adapter to PMD670 and turn off (power standby mode) the unit. Confi rm the connection of the PMD670, Flash Writer and the PC. Then, double click Flash2 icon. Setup screen appears.
Page 14
All manuals and user guides at all-guides.com Select H8/3048B from CPU type Click OK Click Set from Menu bar. Select COMMUNICATION Select Transfer rate in boot-mode : 19200bps Select Max transfer rate : =boot Select Communication port : COMx (Select the same COM Port number that the RS232C cable is connected.) Click OK Click Set...
Page 15
Click OK Finish Confi guration, the next process starts uploading. Writing Insert the update disc (part no : *PMD670CDR) in to CD-R drive. Select fi le name of "pmd670.mot" from the update disc. Click Write from Menu bar Select Write...
Page 16
Verifl ing is started when writing is fi nished. Click OK The upload procedure is completed. Disconnect USB cable from the PMD670, then turn off POWER switch. Check the version number of the fi rmware Refer to 2-page "SERVICE MODE" for "Micro-Proces-...
All manuals and user guides at all-guides.com 8. BLOCK DIAGRAM DC-DC POWER SUPPLY and BATTERY CHARGER LCD DRIVER LCD DISPLAY DC13V or BATT. KEY PANNEL NJU6469 DCIN +3.3V +3.3V VF01 +48V for uP for DSP QF01 +1.6V +-7V for DSP POWER ON/OFF BATTERY MONITOR POWER LED...
All manuals and user guides at all-guides.com 9. SCHEMATIC DIAGRAM L404 PM01-1/10 +3VD R442 BLM11B601 MAIN PCB C416 C424 C414 100n 10/10V 470n CODEC_ADIN CODEC_ADIN CODEC_WS R429 CODEC_WS R425 +3VD 18k% CODEC_BCLK +3VD R421 CODEC_BCLK CODEC_DACOUT CODEC_DACOUT C437 R430 DAI_IN DAI_IN R440 R426...
Page 20
All manuals and user guides at all-guides.com PS01 POWER SW PCB PM01-2/10 PP01 +3VU SU03 SSST01-3A PHANTOM SW +3VD +3VU MAIN PCB POWER JU07 SWITCH RU17 B10B-PH-SM3 +3VU 100k SU01 SSAA22-B B3B-PH JU04 JU01 RU56 RU57 RU58 S3B-PH RU09 RU14 100k MD 2 JU03...
Page 21
All manuals and user guides at all-guides.com PM01-3/10 RX16 +3VD QX07 MAIN PCB DTC114EU CF_INTRQ DSP_INT3 CF_IORDZ CF_IORDZ CF_IOWRZ CF_IOWRZ CF_CS0Z CF_CS0Z JX01 CF_CS1Z CF_CS1Z CON50_CF CF_CD1Z CF_CD1Z CF_CD2Z CF_DATA3 DATA3 CF_CD2Z CF_DATA4 DATA4 CF_DATA5 DATA5 BUS BUFFER QX03 74LCX541 CF_DATA6 DATA6 CF_DATA7...
Page 22
All manuals and user guides at all-guides.com PM01-4/10 DATA3 MAIN PCB TPP5 DATA3 CF_INSZ CF_INSZ CF_CD2Z CF_CD2Z DM:Dumm y CF_CD1Z CF_CD1Z DATA2 +3VD DATA2 CP06 RP11 100n DATA1 RP19 +3VD DATA1 BLM601 JP01 DATA0 DATA0 ADDR13 ADDR13 ADDR14 ADDR14 RP15 ADDR15 ADDR15 BLM11B601...
Page 23
All manuals and user guides at all-guides.com PM01-5/10 MAIN PCB HBIL HBIL CD01 HDS1Z 100n RD05 HDS1Z +3VD HR/WZ HR/WZ QD02 HCSZ M29W800AB HCSZ +3VD +1.6VD TP13 HRDY ADDR0 DATA0 HRDY ADDR1 DATA1 DSP_RSTZ ADDR2 DATA2 DSP_RSTZ HCNTL0 ADDR3 DATA3 HCNTL0 HCNTL1 Flash...
Page 24
All manuals and user guides at all-guides.com AVSW AVSW DVSW DVSW PM01-6/10 CHARGE_ON H:ANALOG POWER ON H:DIGITAL POWER ON CHARGE_ON MAIN PCB BATT_DET BATT_DET Q804 ACIN L801 ACIN 2SA1797 D813 L804 NLF3225 RB160L NLF3225 +3VU PD_MUTE 47uH 10uH C838 C833 PD_MUTE Q817 DTA114EU...
All manuals and user guides at all-guides.com 11. MICROPROCESSOR AND IC DATA QU01 : 64F3048BVF25(FRONT uP) Port Name I/O USE Sig. Name PUP Description Port Name I/O USE Sig. Name PUP Description +3.3V SCAN6 OFF Key scan TIOCA3 Buzzer SCAN7 OFF Key scan HBIL For DSP...
Page 35
All manuals and user guides at all-guides.com QX01:GL641USB Pin No. Name Description Mic ro - PVDD Power supplier for storage device co ntroll er interface Storage device data bus bit 8* Storage device data bus bit 9* Endpoi nt 0 Storage device data bus bit 10* Contro l 8 Bytes FIFO...
Page 36
All manuals and user guides at all-guides.com Q401 : AK4114 DIT Pin Name Function IPS0 Input Channel Select 0 Pin in Parallel Mode Receiver Channel 4 Pin in Serial Mode (Internal biased pin) No Connect NC(AVSS) No internal bonding. This pin should be connected to AVSS. DIF0 Audio Data Interface Format 0 Pin in Parallel Mode Receiver Channel 5 Pin in Serial Mode (Internal biased pin)
Page 37
All manuals and user guides at all-guides.com Q401 : AK4114 DIT Pin Name Function Power-Down Mode Pin When “L”, the AK4114 is powered-down and reset. Master Clock Operation Mode 0 Pin in Parallel Mode CDTO Control Data Output Pin in Serial Mode, IIC= “L”. CAD1 Chip Address 1 Pin in Serial Mode, IIC= “H”.
Page 38
All manuals and user guides at all-guides.com Q402:AK5380VT AGND DGND MCLK Clock Divider ∆∑ Decimation AINL Modulator Filter LRCK SCLK ∆∑ Decimation AINR Modulator Filter Serial I/O SDTO Interface VCOM Voltage Reference Pin Name Description AINR Rch Analog Input Pin AINL Lch Analog Input Pin NC Pin...
Page 39
All manuals and user guides at all-guides.com Q403:AK4380VT-E2 MCLK Clock De-emphasis SMUTE/CSN µP Control Divider VCOM DFS/CCLK Interface DIF0/CDTI AOUTL Modulator LRCK Audio Interpolator Data BICK Interface SDTI AOUTR Interpolator Modulator VREF...
Page 40
All manuals and user guides at all-guides.com QP01:XC9536XL-VQ64-10C JTAG In-System Programming Controller JTAG Port Controller Function Block 1 Macrocells 1 to 18 Function Block 2 Macrocells 1 to 18 Blocks I/O/GCK I/O/GSR I/O/GTS QD03/QD04:M68AW256M70ND1 QD02:M29W800AB80N5 A0-A17 Address Inputs V CC V CC DQ0-DQ15 Data Input/Output...
Page 41
All manuals and user guides at all-guides.com QX02/QX04/QX05 : MC74LVX245DT QX03 : MC74LVX541DT MC74LVX541 LOGIC DIAGRAM DATA NONINVERTING INPUTS OUTPUTS OUTPUT ENABLES PIN ASSIGNMENT FUNCTION TABLE Inputs Output Y IEC LOGIC DIAGRAM &...
Page 42
All manuals and user guides at all-guides.com Q307/QA01/QA02/QA08/QB08:TC74HC4052AFT QB06/QC02/QC03:BU4053BCFV (Refer:HC4053A) Q305:NJM2070M...
Page 43
All manuals and user guides at all-guides.com Q819:BA9741FS-E2...
Page 44
All manuals and user guides at all-guides.com Q820 : NJM2373AF QF01 : NJU6469LFG1...
Page 45
All manuals and user guides at all-guides.com QD01 : TMS320VC5416PGE-160 Table 2–2. Signal Descriptions (Continued) Table 2–2. Signal Descriptions (Continued) TERMINAL TERMINAL TERMINAL TERMINAL I/O † I/O † I/O † I/O † DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION NAME NAME NAME NAME The TMS320VC5416PGE 144-pin low-profile quad flatpack (LQFP) pin assignments are sh INITIALIZATION, INTERRUPT AND RESET OPERATIONS HOST-PORT INTERFACE SIGNALS...
All manuals and user guides at all-guides.com 12. EXPLODED VIEW AND PARTS LIST VERS. POS. PART NO. PART NO. 5 1 1 0 DESCRIPTION 3 X 1 0 ( U) COLOR (FOR EUR) (MJI) 5 1 2 8 1 5 0 B 2 .
All manuals and user guides at all-guides.com 13. ELECTRICAL PARTS LIST NOTE ON SAFETY FOR FUSIBLE RESISTOR : ASSIGNMENT OF COMMON PARTS CODES. RESISTORS The suppliers and their type numbers of fusible resistors : 1) GD05 × × × 140, Carbon film fixed resistor, ±5% 1/4W are as follows;...
Page 48
SP01013370 CF04 EY47501670 TANTL. CHIP 4.7µF 16V EY47501670 SF69 EVQ11L05R H/5MM,160GF CF05 EY47501670 TANTL. CHIP 4.7µF 16V EY47501670 SF70 SS02021680 SLIDE SW. SSSF022-S06N0 ATT SS02021680 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 49
10µF 10V EY10601070 C351 EY10601070 TANTL. CHIP 10µF 10V EY10601070 C822 CER. CHIP 0.01µF ±10% 50V DK96103300 C357 CER. CHIP 47pF ±5% CG 50V DD95470300 C1608JB1H103K NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 50
10µF 10V EY10601070 CB23 CER. CHIP 0.1µF ±10% 50V DK96104300 CA10 CER. CHIP 0.1µF ±10% 50V DK96104300 C1608X7R1H104K C1608X7R1H104K CB24 EY10601070 TANTL. CHIP 10µF 10V EY10601070 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 51
CER. CHIP 0.1µF ±10% 50V DK96104300 CD10 CER. CHIP 1µF 10V F DK98105200 C1608X7R1H104K CD11 CER. CHIP 1µF 10V F DK98105200 CX15 EY10601070 TANTL. CHIP 10µF 10V EY10601070 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 52
NN05221610 R366 CHIP 10kΩ ±5% 1/16W NN05103610 R820 CHIP 100kΩ ±5% 1/16W NN05104610 R367 CHIP 100kΩ ±5% 1/16W NN05104610 R821 CHIP 220Ω ±5% 1/16W NN05221610 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 53
NI05000110 CHIP 0Ω ±5% 1/10W NI05000110 R899 NI01103110 CHIP 10kΩ ±1% 1/10W NI01103110 RA54 CHIP 180Ω ±5% 1/16W NN05181610 RA55 CHIP 180Ω ±5% 1/16W NN05181610 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 54
FC90020110 RC17 CHIP 10kΩ ±5% 1/16W NN05103610 RC18 CHIP 10kΩ ±5% 1/16W NN05103610 RC19 CHIP 1kΩ ±5% 1/16W NN05102610 RP01 CHIP 1MΩ ±5% 1/16W NN05105610 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 55
BA10026210 DIG.TRS. DTA114EU BA10026210 D302 HZ21005000 CHIP DIODE 1SS301,DAN202U HZ21005000 Q327 BA10026210 DIG.TRS. DTA114EU BA10026210 D303 HZ21005000 CHIP DIODE 1SS301,DAN202U HZ21005000 Q328 BA20035210 DIG.TRS. DTC114EU BA20035210 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 56
HC010717K0 IC MC74LVX245DT HC010717K0 2SC4081 (Q,R) 2SC4116 (Y,GR) QX06 HX117971A0 CHIP TRS. 2SA1797 HX117971A0 Q852 HX117971A0 CHIP TRS. 2SA1797 HX117971A0 QX07 BA20035210 DIG.TRS. DTC114EU BA20035210 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 57
FN31010030 EMIFILTER BLM11B102S 1608 FN31010030 LU25 FN31010030 EMIFILTER BLM11B102S 1608 FN31010030 LU26 FN31010030 EMIFILTER BLM11B102S 1608 FN31010030 LU27 CHIP RES. 1kΩ ±5% 1/16W NN05102610 LU32 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Need help?
Do you have a question about the PMD670 and is the answer not in the manual?
Questions and answers